Toro 04130SL Rev C Service Manual Multi Pro 5700 D Preface Publication

F.  Lightly oil bearing journals on spindle shaft. Slide
housing assembly onto spindle (item 1) taking care
to not damage seal or spindle. Make sure that inner
bearing in housing fully seats against spindle shaft
shoulder.
7.  Install thrust plug (item 21) and thrust washer (item
22) into end cap (item 20).  Make sure that thrust plug
and thrust washer are captive on inside of end cap (item
20).
8.
Install new  O--ring (item  13) to end  cap and  then
G. Install outer bearing cone (item 12) onto spindle.
install end cap. Secure cap with retaining ring (item 17).
NOTE:  The planetary shim kit includes the retaining
ring and several thrust washers with thickness in in-
cremental steps of 0.004 in. (0.10 mm).
9.  Check operation  of planetary  wheel drive.  With a
constant turning force applied, rotation of the planetary
should be  consistent. If there  is more drag at  certain
points, gears  are not  rolling freely  and the  planetary
shouldbeexaminedforimproperassembly   ordamaged
components.
H. Measurethicknessofthrustwasher(item14)that
was  removed  during  disassembly.  Choose  new
thrustwasherofequalthicknessorthenextavailable
thickness from thrust washers in the shim kit.
10.If planetary wheel drive assembly is installed on ma-
chine:
I.   Apply a light coating of oil to spindle shaft, thrust
washer (item 14) and  new retaining ring (item 15).
Install thrust washer onto spindle shaft.
A.  Install front wheel assembly.
WARNING
WARNING
Failure to maintain proper wheel lug nut torque
could result in failure or loss of wheel and may
result in personal injury.
If retaining ring (item 15) is not fully installed in
spindle groove, loss of wheel and personal inju-
ry may result.
B.  Lower machine from jack stands. Torque wheel
lugnutsinacrossingpatternfrom70to90ft--lb(95to
J.  Carefully install new retaining ring (item 15) into
the spindle  shaft groove taking  care to  not distort
ring. If the proper thrust washer has been installed,
the retaining ring should fit tightly between the thrust
washer and spindle  groove. Tap the OD of  the re-
taining ring starting in the center and working out to-
ward each end  to ensure that  the retaining ring is
properly seated into the spindle groove. Make sure
that retaining ring ID is fully seated to spindle shaft
groove.
122
N--m).
C. Make  sure drain  plug is  installed  in bottom  of
brake assembly. Fill planetary wheel drive/brake as-
sembly withSAE85W--140gearlubetoproperlevel.
Capacity is approximately 16 oz. (0.47 l) per wheel.
K.  After retaining ring  is installed, make  sure that
there is no endplay in assembly. If required, remove
retaining ring and install a thrust washer of different
thickness to adjust endplay.
L.  Install new O--ring (item 13) into groove in hous-
ing.
4.
Install secondary carrier (item 28), secondary  gear
(item 27) and primary carrier (item 26) making sure that
carrier gear  teeth align  with ring  gear and  spline on
spindle shaft.
5.
shaft,slidegearontoshaftandsecurewithretainingring
(item 23).
If primary  gear (item 24)  was removed from  drive
6.
making sure that  drive shaft spline  aligns with carrier
gears.
Install drive shaft  assembly (items 25,  24 and 23)
Page 7 -- 18   Rev. C
Chassis
Multi Pro 5700--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 212 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website