Toro 04130SL Rev C Service Manual Multi Pro 5700 D Preface Publication

Removal (Fig. 45)
Park the machine on a level surface, engage parking
brake, and stop engine.  Remove key from the ignition
switch.
3.  Lubricate new o–rings and connect hydraulic hoses
to steering control valve (Fig. 46). Tighten hose connec•
tions.
1.
4.  Position dash  panel to front  hood and secure  with
fasteners (Fig. 47).
CAUTION
5.  Check fluid level in hydraulic oil reservoir and adjust
as required (see Operator’s Manual).
Rotate steering wheel and depress traction ped•
al in both forward and reverse to relieve hydrau•
lic  system pressure  and to  avoid  injury from
pressurized hydraulic oil.
6.  After assembly is completed, operate steering cylin•
der to verify that hydraulic hoses and fittings are not con•
tacted by anything and that there are no leaks.
5
2.
Operate  all hydraulic  controls to  relieve  hydraulic
system pressure.
3.
Read the  General  Precautions for  Removing and
Installing Hydraulic System Components at  the begin•
ning of the Service and Repairs section of this chapter.
3
4.
Label all hydraulic connections for reassembly pur•
poses. Clean hydraulic hose ends prior to disconnecting
the hoses.
1
5.
Remove fasteners  that secure dash  panel to front
hood (Fig. 47). Front edge of panel is secured with four
screws and weldnuts.  Sides of panel are  fastened
2
4
(4)
with four (4) screws and flange nuts. Carefully slide dash
panel up  steering column to  allow access  to steering
control valve.
Figure 46
1.
2.
3.
Steering control valve
Hyd hose (left turn)
Hyd hose (right turn)
4.
5.
Hyd hose (from pump)
Hyd hose (to oil cooler)
6.
Disconnect hydraulic hoses connected to the steer•
ing control  valve. Allow hoses  to drain into  a suitable
container. Cap  or plug  openings of control  valve and
hoses to prevent contamination.
1
7.
Support steering control valve to prevent it from fal•
ling during removal.
2
8.
Loosen and remove four (4) cap screws that secure
steering column and steering control valve to machine
frame.
3
9.
Slide steering  valve from control  column. Remove
control valve from machine.
3
Installation (Fig. 45)
1.
Slide steering  control valve  onto steering  column.
Secure steering column and control valve to frame with
four (4) cap screws.
Figure 47
1.
2.
Steering column
Dash front edge screw
3.
Dash side screw
2.
Remove caps and  plugs from disconnected  hoses
and fittings.
Multi Pro 5700–D
Page 4 – 49
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 212 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website