Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Pivot Yoke Removal (Fig. 7)
Park vehicle  on a  level surface, turn  on/off switch
OFF, set parking brake and remove key from the on/off
switch.
2.  Secure  pivot yoke to  the front  frame tab  with cap
screw and  hardened washer.  Torque cap  screw from
1.
240
to 290 ft–lb (325 to 393 N–m).
3.  Secure pivot  yoke to  the rear  frame with four  cap
screws and flat washers.
2.
Open the battery circuit by carefully removing one of
the battery cables  (see Opening Battery Circuit  in the
General Information  section of  Chapter 3 –  Electrical
System).
4.  Install seat base  to the front frame (see Seat Base
Installation in this section).
5.
Install cargo bed to the rear  frame (see Cargo Bed
3.
Remove cargo bed from the rear frame (see Cargo
Installation in this section).
Bed Removal in this section).
6.
Reconnect removed battery  cable to battery termi-
4.
Base Removal in this section).
Remove seat base  from the front  frame (see Seat
nals. Install lock  washer and nut on  battery terminals.
Torque nuts from 115 to 125 in–lb (13 to 14.1 N–m).
3
WARNING
2
Make sure  all tires  are chocked to  prevent the
machine from moving. Before removing the pivot
yoke,  make   sure  front   and  rear  frames   are
supported  with jack  stands.  Support both  the
front and back of each frame.
2
1
5.
ing the pivot yoke to the rear frame (Fig. 10).
Remove four (4) cap screws and flat washers secur-
4
6.
the pivot yoke to the front frame tab.
Remove cap screw and hardened washer securing
5
6
Figure 10
WARNING
1.
2.
3.
Pivot yoke
4.
5.
6.
Flange lock nut
Front frame
Diamond pattern
Cap screw & flat washer
Rear frame
Support pivot  yoke while  removing it  from the
front  frame  to  prevent  dropping and  causing
serious injury and damage to the machine.
7.
nuts securing the pivot yoke to the front frame. Remove
pivot yoke from the machine.
Remove four flange  head screws and flanged lock
Pivot Yoke Installation (Fig. 7)
WARNING
Support pivot yoke while installing it to the front
frame to prevent dropping and  causing serious
injury and damage to the machine.
1.
Position pivot yoke to the front frame so the diamond
pattern faces up  (Fig. 10). Secure yoke to  front frame
with  four flange  head screws  and  flanged lock  nuts.
Tighten lower two fasteners first, then tighten upper two
fasteners.
Chassis (Rev. B)
Page 5 – 18
Workman e2050/e2065
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website