Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Installation (Fig. 3)
Burnish Brake Shoes
IMPORTANT:On Workman e2050 vehicles, the brake
actuator levers must be positioned below the trans-
axle mount. On Workman e2065 vehicles, the levers
should be  positioned above  the transaxle  mount.
When positioned correctly, the  brake actuator lev-
ers will point toward the rear of the vehicle (Fig. 4).
To  provide  maximum  brake  performance  after  rear
brake shoes are replaced, burnish new brake shoe lin-
ings.
IMPORTANT:To prevent brake  overheating, do not
drive vehicle with the brakes applied.
IMPORTANT:When burnishing brake shoes, do not
allow the brakes  to lock up.  Also, allow brakes  to
cool between stops.
1.
brake assembly to the transaxle.
If brake assembly was removed from axle, position
A.  Secure brake assembly to the transaxle with four
1.
Drive vehicle  while making 6  to 7 normal  stops at
about 200 ft (60 m) intervals while traveling at 10 to 15
mph (16 to 24 KPH).
(4)
cap screws and nuts. Torque screws from 15 to 19
ft–lb (20 to 26 N–m).
B.  On Workman  e2065, position  hydraulic  brake
line to wheel cylinder. Connect brake line to wheel
cylinder.
2.
the reverse direction. This will self adjust the clearance
between the brake shoes and drum.
Make several normal stops with the vehicle going in
C. Secure brake cable bracket to the brake actuator
lever with clevis pin and cotter pin (Fig. 4).
Workman e2050 Shown
2.
Highway Components Model 12 (Electric) Maintenance
Manual at the end of this chapter).
Install axle shaft into transaxle (see the Spicer Off–
3.
hole in drum aligns with hole in wheel hub on axle.
Slide brake drum onto wheel  hub making sure that
3
4
4.
Position wheel  assembly to  the vehicle with  valve
stem facing out and secure with five (5) lug nuts. Torque
lug nuts in a criss–cross pattern from 45 to 65 ft–lb (61
to 88 N–m).
1
2
5.
Lower vehicle to ground.
Figure 4
CAUTION
1.
2.
Cotter pin
Clevis pin
3.
4.
Brake cable bracket
Brake actuator lever
After  servicing  the  brakes,  always  check  the
brakes in a  wide open, level area that  is free of
other persons and obstructions.
6.
Check and adjust brakes (see Operator’s Manual).
Workman e2050/e2065
Page 4 – 9
Transaxle and Brakes (Rev. B)
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website