Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Main and Accessories Contactors
Two contactors (solenoids) are  used on the Workman
e2050 and e2065 for circuit control.
5
4
1
The main contactor provides current to the vehicle con-
troller and is  energized when the  on/off switch is ON.
The main contactor is located under the controller cover
beneath the bed (Fig. 31).
2
The accessories contactor provides current to the head-
lights, horn and optional electrical accessories. The ac-
cessories contactor is energized when the on/off switch
is ON. The accessories contactor is located beneath the
dash panel.
3
6
Testing
NOTE:  Prior to taking small resistance readings with a
digital multimeter, short  the meter test leads  together.
The meter will display a small resistance value (usually
Figure 31
1.
2.
3.
Main contactor
4.
Fuse (F1)
Positive battery cable
Isolator
Cable to controller B+
Wire harness connector
5.
6.
0.5
ohms or less) that is due to the internal resistance of
the meter and  test leads. Subtract this value  from the
measured value of the component you are testing.
1
1.
Make sure on/off switch is turned OFF. Open the bat-
tery circuit by removing one of  the battery cables (see
Opening Battery Circuit in the General Information sec-
tion of this chapter and Fig. 32).
2
A
2.
Locate contactor that is to be tested. Disconnect all
vehicle harness electrical  connections from contactor.
Note wire  connector  locations on  contactor for  reas-
sembly purposes.
4
3.
Using jumper wires, apply 48 VDC directly across the
Figure 32
contactor coil posts (Fig. 33). The contactor should click.
With the contactor coil energized, resistance across the
main contact posts should be less than 1 ohm.
1.
Negative cable to vehicle
2.
Positive cable to vehicle
4.
Remove voltage from contactor coil posts. The con-
4
4
3
tactor should click. With the contactor coil not energized,
resistance across the main contact posts should be infi-
nite ohms.
2
5.
(Fig. 33):
Measure resistance across the contactor coil posts
3
3
A.  For the main contactor, the resistance should be
approximately 126 ohms.
B.  For  the  accessories contactor,  the  resistance
should be approximately 200 ohms.
4
4
1
3
Figure 33
1.
2.
Main contactor
Accessories contactor
3.
4.
Main contact posts
Contactor coil posts
Electrical System (Rev. B)
Workman e2050/e2065
Page 3 – 20
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website