Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Brush Service
Check the brush springs for correct alignment on the
back of the  brush. A brush spring that  does not apply
equal pressure on the center of the brush will cause the
brush to wear unevenly. Check for correct clearance and
freedom of brush movement in the holder.
3.  It is also recommended that the field be coated with
PD George 1000–70 or RanBar B–535–5S varnish for
proper insulation  protection. Both  recommended var-
nishes are Class H water–soluble  varnishes. A similar
air–dry  varnish may  also be  used  providing it  has a
Class H rating.
1.
4.
be torqued from 250 to 300 in–lb (28.3 to 33.9 N–m) (Fig.
60).
Screws securing the pole pieces to the frame should
2.
(16
even wear or show signs of overheating, such as discol-
ored brush shunts and brush springs.
Replace brushes that are worn to a length of 0.620”
mm). Also, replace brushes if they show signs of un-
2
3
3.
Brushes should always be replaced in complete sets
of eight. Use identical replacement parts; do not substi-
tute brush  grades as the brushes  are matched to  the
motor type and application to provide the best service.
Substituting brushes of the wrong grade can cause pre-
mature commutator failure and  excessive brush wear.
Remove old brushes and replace with identical replace-
ment parts.  Hold brush shunts  in position  and torque
brush screws from 18 to 22 in–lbs (2 to 2.5 N–m) (Fig.
1
Figure 58
1.
2.
Motor housing
Puller
3.
Arbor press
60).
Make sure brushes move freely in the holders and
that shunts do not interfere with brush spring movement.
4.
Make sure  the brush box  assembly is tight  on the
1
commutator end head. Replace brush box assemblies
in the commutator end head if they are physically dam-
aged or brush holders are loose on the brush plate.
5.
using the following procedure (Fig. 59):
Brush springs should be checked for proper tension
2
3
A.  Place paper strip between brush face and com-
mutator. Hook spring scale as shown.
B.  Pull spring scale  on a line directly  opposite the
line of force exerted by the brush spring.  When the
paper strip begins to move freely, read the spring ten-
sion on  the scale.  Brush tension  for a  new brush
should be 65 ounces  (1820 grams) and for a  worn
brush should be 40 ounces (1120 grams).
Figure 59
3.
1.
2.
Spring scale
Brush spring
Paper
Frame and Field Service
2
2
1.
Motors that  have been disassembled  for servicing
should be given a complete inspection of the frame and
field assembly. If  damage to the field coils  or frame is
found, replace traction motor. Individual frame and field
components are not available.
1
2.
Accumulated carbon dust, grease and other foreign
material can produce a ground path from the field wind-
ing to the frame. The frame and field should be cleaned
with Safety–Kleen 105  washing solvent or equivalent.
After cleaning, the frame and field must be oven–dried
for one hour at 300oF (148o C) to remove any cleaning
Figure 60
2.
1.
Brush screw
Pole piece screw
residue.
Workman e2050/e2065
Electrical System (Rev. B)
Page 3 – 39
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website