Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Inspection (Fig. 6)
Inspect brake drums.
Assembly (Fig. 6)
1.
IMPORTANT:Brake  shoe lining  surfaces  must  be
free of grease, oil and other foreign matter.
IMPORTANT:Brake drum  machining is not  recom-
mended. Replace brake drums as a set to maintain
equal braking forces.
1.  Apply a light film of lubricant to the following:
A.  Ledges on which the brake shoes rest.
B.  Pin surfaces on adjuster levers.
A.  Clean  drums  with   denatured  alcohol.  Check
braking surface diameter in at least three places.  If
the  diameter exceeds  6.320” (16.05  cm),  replace
both brake drums.
C. Anchor block surface that contacts shoe webs.
D. Both surfaces of belleville washers that are posi-
tioned between adjuster levers and backing plate.
B.  Replace drums that are cracked, deeply grooved,
tapered,  significantly  out–of–round,  scored,  heat
spotted or excessively rusted.
2.
If removed, position lubricated belleville washer be-
tween lever adjuster and backing plate. Secure adjuster
to backing plate with washer and bolt. Torque bolt from
C. Minor scoring can be removed with sandpaper.
110
to 120 in–lb (12.4 to 13.6 N–m).
2.
Inspect brake shoe linings.
3.
with two (2) washer head screws.  Torque screws from
110 to 120 in–lb (12.4 to 13.6 N–m).
If removed, secure  wheel cylinder to backing plate
IMPORTANT:Replace brake shoes as a set (all four
shoes) to maintain equal braking forces.
A.  Replace brake  shoes if damaged  or if  lining is
worn to 1/16” (1.6 mm). Replace if lining is contami-
nated by oil, grease, or other fluids.
4.
ver into slot and dust cover in backing plate.
If removed from backing plate, slide parking brake le-
5.
Position brake  shoes to  backing plate. Make  sure
NOTE:  Overheated springs lose their tension, and can
cause brake linings to wear out prematurely.
that each shoe is  properly positioned at anchor block,
parking brake lever, wheel cylinder and pin on adjuster
lever. Secure  shoes  to backing  plate with  shoe  hold
down cups and springs.
B.  Inspect brake  shoe webbing,  upper  and lower
springs, and shoe  hold down springs for overheat-
ing. Overheating is indicated by a slight blue color. In-
spect brake shoe webbing for deformation. Replace
parts as necessary.
CAUTION
C. Inspect  hold  down  pins on  adjuster  levers for
bends, rust and corrosion. Replace as necessary.
Be  careful   when  installing  springs   to  brake
shoes.  The springs  are under  heavy  load and
may cause personal injury.
3.
Inspect backing plate  surfaces, which contact  with
the  brake  shoes for  grooves  that  may  restrict shoe
movement.  Replace plate  if  grooves  can not  be  re-
moved by light sanding  with emery cloth or other suit-
able  abrasive.  Replace  plate  if  cracked,  warped  or
excessively rusted.
6.
Secure brake shoes with upper and lower springs.
4.
ers if deformation or excessive rust is found.
Inspect adjuster levers for deformation. Replace lev-
5.
Replace parking brake cables if frayed, stretched or
kinked.
Workman e2050/e2065
Page 4 – 13
Transaxle and Brakes (Rev. B)
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website