Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Traction Motor Brushes
The traction motor in the Workman e2050/e2065 uses
eight (8) brushes. Traction motor brushes should be in-
spected every 500 hours of operation or annually.
4
2
3
Inspection
1.
Make sure that on/off switch is OFF. Raise and latch
bed to allow access to traction motor.
2.
Open the battery circuit by carefully removing one of
1
the battery cables  (see Opening Battery Circuit  in the
General Information section of this chapter).
3.
headband to allow inspection of a brush at the top of the
motor.
Unlatch headband of  traction motor and reposition
Figure 48
4.
If end of brush is even with the brush holder (Figs. 48
1.
2.
Brush
Brush holder
3.
4.
Brush spring (tensioned)
Brush spring (released)
and 50), brushes should be removed from motor for in-
spection and measurement (see Traction Motor Service
in this section).
1
5.
In most instances, wear of all traction motor brushes
should be similar to wear found on the top brushes. If in-
spection of remaining brushes is  needed or if brushes
require replacement, traction motor should be removed
from vehicle  (see  Traction Motor  and Traction  Motor
Service in this section).
6.
If vehicle is often operated in severely dirty environ-
ments, brush should be removed from motor to allow in-
spection of mating  surface of brush (Fig. 49).  If brush
surface  is  rough, pitted,  arced  or  scored,  additional
brush  and/or motor  inspection  should  be  completed
(see Traction Motor and Traction Motor  Service in this
section).
2
Figure 49
7.
Visually inspect commutator surface of motor arma-
1.
Removed brush
4
2.
Cap screw
ture. If  commutator surface  is rough,  pitted, arced  or
scored,  additional  motor  inspection should  be  com-
pleted (see Traction Motor and Traction Motor Service
in this section).
2
8.
installed in brush holder and tensioned by spring. Refit
headband to traction motor and latch headband.
After brush inspection, make sure brush is correctly
1
3
9.
terminals. Install lock washer and nut on battery termi-
nals. Torque nuts from 115 to 125 in–lb (13 to 14.1 N–m).
Carefully connect removed battery cable  to battery
4
10.Lower
bed.
1
Figure 50
1.
2.
Brush holder (side view)
Normal brush
3.
4.
Worn brush
Brush shunt wire
Workman e2050/e2065
Electrical System (Rev. B)
Page 3 – 33
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website