Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Removal (Fig. 1)
Park vehicle  on a  level surface, turn  on/off switch
3.  Insert steering shaft up through the steering column.
Place dust cover onto the shaft.
1.
OFF, set parking brake and remove key from the switch.
4.  Secure steering column to the mounting plate on the
frame with four (4) carriage screws and flange lock nuts.
2.
Open the battery circuit by carefully removing one of
the battery cables  (see Opening Battery Circuit  in the
General Information  section of  Chapter 3 –  Electrical
System).
NOTE:  Apply antiseize lubricant to  the steering gear-
box shaft before installing steering shaft knuckle.
5.
Position knuckle of the lower steering shaft onto the
3.
mechanism (see Front Hood Removal in this section).
Remove front  hood to gain  access to the  steering
gearbox shaft. Secure knuckle to the steering gearbox
shaft with cap screw and lock washer.
4.
Remove  steering  wheel  cover carefully  from  the
6.  Connect both tie rods to the Pitman arm on the steer-
ing gearbox (see Lower Steering Installation in this sec-
tion).
steering wheel. Remove nut and lock washer securing
the steering  wheel to the  steering shaft. Pull  steering
wheel from the shaft.
NOTE:  Apply antiseize lubricant  to the steering  shaft
5.
lower  steering shaft  knuckle to  the  steering gearbox
shaft. Pull knuckle from the gearbox shaft.
Remove cap  screw and  lock washer  securing the
splines before installing the steering wheel.
7.
Position front tires straight ahead. Position steering
wheel to  the steering  shaft so  that the  leg of the  “Y”
formed by the wheel struts is directed towards the oper-
ator platform.
6.
securing the steering column to the  mounting plate on
the frame.
Remove four (4) flange lock nuts and carriage bolts
8.
Secure steering wheel to shaft with lock washer and
7.
cover if damaged. Slide steering shaft out of the steering
column.
Remove dust cover from the steering shaft. Replace
nut. Torque nut from 13 to 17 ft–lb (18 to 23 N–m). Install
steering wheel cover to steering wheel.
9.
Install front hood to the frame and fenders (see Front
8.
Disconnect both tie rods from the Pitman arm on the
Hood Installation in this section).
steering gearbox (see Lower Steering  Removal in this
section).
10.Reconnect
nals. Install lock  washer and nut on  battery terminals.
Torque nuts from 115 to 125 in–lb (13 to 14.1 N–m).
removed battery cable  to battery termi-
9.
Remove three (3) flange  lock nuts and cap screws
securing the steering gearbox to the tower plate on the
front frame. Remove gearbox from the tower plate.
11.
(see Operator’s Manual).
Check front wheel alignment  and adjust if required
Installation (Fig. 1)
1.
Position steering gearbox  to the tower plate  of the
front frame with the Pitman arm facing down and to the
rear. The gearbox shaft  must be to the left  side of the
tower.
2.
(3)
Secure steering gearbox to the tower plate with three
cap screws and flange lock nuts.
Workman e2050/e2065
Page 5 – 7
Chassis (Rev. B)
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website