Toro 04127SL Rev C Service Manual Workman E2050 E2065 Preface Publication

Removal (Fig. 8)
Park machine  on a level  surface, stop engine,  set
3.  Align  caliper mounting  holes with  spindle. Secure
caliper with two (2) cap screws and lock washers.
1.
parking brake and remove key from the ignition switch.
4.  Install brake hose to caliper.
5.
to 65 ft–lb (61 to 88 N–m).
Install front wheel assembly. Torque lug nuts from 45
WARNING
6.
Lower machine to ground.
Before jacking up the machine, review and follow
Jacking Instructions in Chapter 1 – Safety.
7.  Bleed brakes (see Bleed Brake System in this  sec-
tion).
2.
off the ground and place blocks beneath the frame.
Chock wheels not being jacked up. Jack front wheel
CAUTION
3.
Remove  front  wheel   from  machine  (see   Lower
Steering and Front Wheel Removal).
After  servicing  the  brakes,  always  check  the
brakes in a  wide open, level area that  is free of
other persons and obstructions.
4.
Clean hydraulic brake  line area of brake  caliper to
prevent contamination.  Loosen and  disconnect brake
line from  caliper. Plug brake line  and position it  away
from caliper.
8.
Check brake operation.
5.
secure the brake caliper to the spindle.
Remove two (2) cap screws  and lock washers that
3
6.
Slide brake caliper from brake rotor and remove cali-
per from machine.
2
7.
9):
If necessary, remove brake  pads from caliper (Fig.
A.  Remove anti–rattle clip from caliper.
B.  Remove pins from  caliper by prying with  a flat
blade screwdriver through loop in pins.
1
C. Slide brake pads from caliper. For assembly pur-
poses, note orientation of inner and outer  pads as
the pads are not the same.
Figure 9
1.
2.
Brake pad
Pin (2 used)
3.   Anti–rattle clip
D. Replace the brake pads if the friction material is
worn to less than 1/32” (0.8 mm).
Installation (Fig. 8)
If brake pads were removed from caliper, install pads
1.
(Fig. 9):
A.  If brake pads are being replaced, it will be neces-
sary to  push caliper  pistons back into  the caliper
bore before installing new pads.
B.  Slide brake pads into caliper. Make sure that fric-
tion material on pads is toward brake rotor position.
C. Secure pads into caliper with two (2) pins. Make
sure that  pins snap into caliper  slots. Install anti–
rattle clip to caliper, pin and brake pads.
2.
Slide brake caliper onto brake rotor. Make sure that
rotor is between brake pads.
Workman e2050/e2065
Page 4 – 17
Transaxle and Brakes (Rev. B)
Product Specification
CategoriesLawn Mower Manual, Toro Lawn Mower Manual
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 120 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Product TypeWalk Behind Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website