Toro 08160SL Workman MD MDX Service Manual

5.
Support steering  column to prevent  it from falling.
NOTE:  Apply antiseize lubricant to the steering  gear-
box  input   shaft  before  installing   to  steering  shaft
knuckle.
Remove four (4) flange nuts and carriage screws secur-
ing the  steering column to  the mounting plate on  the
frame.
5.
Position knuckle of the lower steering shaft onto the
6.
Replacecoverifdamaged.Slidesteeringshaftoutofthe
steering column.
Remove dustcover (item 13) fromthe steering shaft.
gearbox  input shaft.  Secure  knuckle to  the  steering
gearbox shaft with cap screw and lock washer.
6.
Make sure that collar (item 14) is just below steering
7.
steering gearbox (see Lower Steering and Front Wheel
Removal in this section).
Disconnect both tie rods from the Pitman arm on the
column.  If  necessary, re--position  collar  on  steering
shaft. Apply  Loctite #242 (or  equivalent) to collar  set
screw and secure collar with set screw.
8.
secure the steering gearbox  to the tower plate on the
front frame. Remove gearbox from the tower plate.
Remove four (4) cap screws and lock washers that
7.  Place dust cover onto the steering shaft.
8.
Connect both tierods to thePitman armon thesteer-
ing  gearbox  (see Lower  Steering  and  Front  Wheel
Installation in this section).
Assembly (Fig. 4)
1.
Position steering gearbox to  the tower plate of the
NOTE:  Apply antiseize lubricant to  the steering shaft
taper before installing the steering wheel.
front frame with the Pitman arm facing down and to the
rear. The gearbox shaft must  be to the left side of the
tower.
9.
Position  front tires  straight  ahead. Slide  steering
wheel onto the steering shaft so that the leg of the “Y”
formed by the wheel struts is directed towards the oper-
ator platform.
2.
(4)
Secure steering gearbox to the tower plate with four
cap screws and lock washers. Torque screws from
175
to 225 in--lb (20 to 25 N--m).
10.Secure
steering wheel to shaft with flat washer and
3.
ing shaft. Insert steering shaft up through the  steering
column.
Makesurethatcollar(item14)ispositionedonsteer-
nut. Torque  nut from 18  to 22 ft--lb  (25 to 29  N--m).
Install steering wheel cover to wheel.
11.
Lower front hood.
4.
frame with four (4) carriage screws and flange nuts.
Secure steering column to the mounting plate on the
12.Check
Wheel Toe--in in the Adjustments section of this chap-
ter).
front  wheel  alignment  (see  Adjust  Front
Workman MD/MDX
Page 7 -- 11
Chassis
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 178 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website