Toro 08160SL Workman MD MDX Service Manual

Drive Clutch Inspection
Inspect the tapered ends of the crankshaft and pri-
2
1.
mary fixed  sheave for scratches.  If either is  severely
scratched, replace component. If scratches are minor,
burnish the component with emery cloth.
1
2.
worn, replace all cam weights as a set.
Check the surface  of the cam weights  (Fig. 17). If
Figure 17
3.
is found, replace all rollers as a set.
Check the rollers (Fig. 18). If binding or uneven wear
1.
Cam weight
2.
Worn contact surface
4.
abrasivepaper.Ifthechrome--platedsurfaceofthebolts
or pins is scaled off, replace the damaged components.
Clean pilot bolts and roller pins with 800 -- 1000 grit
2
3
5.
wear and/or fraying. If surface  is worn/frayed, replace
component.
Check thecontact surface ofthemovable sheave for
6.
fatigued.
Inspect the clutch spring and replace if damaged or
1
Figure 18
Drive Clutch Assembly (Fig. 15)
1.
2.
Roller
3.
Roller uneven wear
Weight contact surface
1.
If removed, install rollers, washers and roller pins to
spider. Roller pins should  be lubricated with Toro part
(see Special Tools).
#104--7011
2.
Lubricate  cam weights  with Toro  part #104--7011
(see Special Tools). Make sure lubricant penetrates to
pilotboltsbyrotatingandslidingtheweightssidetoside,
or remove weights if needed to  lubricate properly. As-
semble cam weights to moveable sheave as follows:
2
1
1
2
A.  Make sure the threads of the pilot bolts are clean
and dry.  Apply Loctite #271  (or equivalent)  to the
threads of each bolt.
3
1
IMPORTANT: To  maintain  the   balance  of  the
clutch, all pilot bolts must be installed with their
threads pointing  in a  clockwise direction (Fig.
19).
2
Figure 19
1.
2.
Pilot bolt
Pilot bolt threads
3.
Moveable sheave
B.  Immediately install  new lock  nuts  on the  pilot
bolts. Tighten nuts until they  just touch the sheave
casting. Never reuse lock nuts.
3.
Apply Loctite #271 (or equivalent) to the threads of
the fixed sheave post.
4.
moval tool kit  (see Special Tools). Make sure  to align
matchmark made during disassembly.
Installspidertothefixedsheavepostusingspiderre-
5.
Torque spider to 100 ft--lb (136 N--m).
6.
able  sheave with  three  (3) cap  screws.  Torque cap
Position cover to clutch.  Secure cover to the mov-
screws from 75 to 100 in--lb (8.5 to 11.3 N--m).
Workman MD/MDX
Page 5 -- 13
Drive Train
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 178 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website