Toro 08160SL Workman MD MDX Service Manual

IMPORTANT: Take care to  not damage the engine,
fuel hoses, electrical harness  or other parts while
lowering the engine tray assembly.
6.  Positionselectlever  assembly andshiftcables tothe
transaxle (Fig. 24). Secure select lever assembly to the
selector shaft with lock nut. Secure both shift cables to
the cable bracket with jam nuts.
13.Carefully
moveenginetrayassemblytowardtherear
ofthevehicle  toclear mounts on swing arm. Then,lower
engine tray enough  to allow the  transaxle and driven
clutch to be removed from the rear of the vehicle. Sup-
port engine tray in this position to prevent it from shifting
or falling.
7.  On Workman MD, secure governor and cable brack-
ets to the transaxle as follows (Fig. 23).
A.  Position governor and cable brackets withcables
as a complete unit to the transaxle case and gover-
nor shaft.
14.Remove
head screws (item 16) that secure the transaxle to the
engine tray.
four (4)  flange nuts (item  12) and flange
B.  Secure cable bracket to the transaxle case with
both lock nuts.
C. Align scribe marks on  the governor bracket and
shaft.  Secure  bracket to  the  shaft  with both  set
screws.
15.Carefully
of the vehicle.
remove transaxle assembly from the rear
Installation (Fig. 22)
8.
Secure both  battery cables to  the passenger side
1.
cure transaxle to the tray with four (4) flange nuts (item
Position transaxle assembly to the engine tray. Se-
axle tube with cable ties.
9.
Install drive belt to the driven clutch.
muffler  to  machine  (see  Exhaust  System
12)
2.
tioned in the swing arm so that the flange is positioned
between the swing arm bracket and engine tray location
(Fig. 25).
and flange head screws (item 16).
10.Install
Make sure that isolation mounts (item 17) are posi-
Installation in the Service and Repairs section ofEngine
Chapter).
11.
Install  both brake  assemblies  and wheels  to  the
transaxle (see  Rear  Wheel and  Brake Installation  in
Chapter 7 -- Chassis).
IMPORTANT: Take care to  not damage the engine,
fuel hoses, electrical harness  or other parts while
raising the engine tray assembly.
12.Install
cargo box to the frame (see Cargo Box Instal-
lation in Chapter 7 -- Chassis).
3.
Usinghoist,carefullyraiseenginetrayassemblyand
align it with swing arm mounting points.
13.Verify
proper  ground  speed (see  Adjust  Ground
Speed in the Adjustments section of this chapter).
4.
Secure the transaxle to the swing arm with four (4)
cap screws (item 3) and flat washers (item 2).
14.Check
brakes for proper operation.
5.
Secure engine tray to the swing arm:
A.  Align engine tray to swing arm. Insert cap screw
with flat washer up through swing arm bracket, isola-
tion mount and engine tray (Fig. 25).
B.  Secure cap screw with flange nut.
Drive Train
Page 5 -- 18
Workman MD/MDX
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 178 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website