Toro 08160SL Workman MD MDX Service Manual

3.
the clutch cover and the clutch components.
Using compressed air, thoroughly clean the inside of
2.  Thoroughly clean the tapered surfaces of the engine
crankshaft and drive clutch.
4.
14
Avoid getting lubricant on drive belt.
Lubricate the clutch components as shown in Figure
using Toro Dry Lubricant Spray (see Special Tools).
3.  Slide drive clutch onto the engine shaft.
4.
Apply Loctite #242 (or equivalent) to the threads of
the cap screw.
5.
screws. Torque cap screws from 75 to 100 in--lb (8.5 to
11.3
Install cover to clutch and secure with three (3) cap
5.
Torque cap screw from 25 to 30 ft--lb (34 to 40 N--m).
Secure clutch to shaft with  cap screw and washer.
N--m).
6.
7.
Carefully install plastic cap to the drive clutch.
6.
Lower and secure cargo box.
Drive Clutch Removal (Fig. 12)
Park machine on  a level surface, stop  engine, set
Install starter/generator  V--belt  to the  engine  and
starter pulley. Adjust belt tension.
1.
parking brake and remove key from the ignition switch.
Raise and support cargo box.
8.
9.
Install drive belt to the drive clutch.
Lower and secure cargo box.
2.
3.
Remove drive belt from the drive clutch.
Remove starter/generator  V--belt from  the engine
pulley.
2
2
4.
5.
Carefully remove plastic cap from the drive clutch.
Remove cap screw and  washer securing the drive
clutch to the engine tapered shaft.
1
IMPORTANT: Grease  end  of  clutch  removal  tool
lightly to prevent  wear. Prevent damage  to clutch
threads;  thread tool  only  enough to  remove  the
clutch.
2
Figure 13
6.
Use clutch removal  tool (see Special  Tools) to re-
1.
Clutch cover
2.
Cap screw
move drive clutch from the engine tapered shaft.
7.
If necessary, remove four  (4) cap screws and lock
washersthatsecuretheenginestarterpulleyandstarter
spacer to the drive clutch.  Remove pulley and spacer
from clutch.
Drive Clutch Installation (Fig. 12)
1.
If removed, install engine starter pulley to the drive
clutch as follows:
A.  Insert four (4) cap screws through lock washers,
pulley and spacer.
B.  Apply Loctite #242 (or equivalent) to the threads
of the cap screws.
C. Secure  pulley and  starter spacer  to the  clutch
with cap screws.
Figure 14
Workman MD/MDX
Page 5 -- 11
Drive Train
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 178 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website