Toro 08160SL Workman MD MDX Service Manual

6.
brackets from the transaxle as follows (Fig. 23).
On  Workman  MD,  remove  governor   and  cable
1
3
A.  Scribe mark across governor bracket and gover-
nor shaft to help installation. Loosen both set screws
securing the bracket to the shaft.
4
2
B.  Remove both lock nuts securing the cable brack-
et to the transaxle case. Remove both brackets and
cables as a complete assembly  from the transaxle
case and governor shaft.
5
7.
Remove lock nut  that secures the select  lever as-
sembly to the transaxle selector shaft (Fig. 24). Loosen
jam nuts securing both shift cables to the cable bracket
on the transaxle. Separate select lever and shift cables
assembly from the transaxle.
Figure 23
1.
2.
3.
Scribe mark
Governor bracket
Set screw (2 used)
4.
5.
Lock nuts
Cable bracket
WARNING
Beforejackingupthemachine,reviewandfollow
Jacking Instructions in Chapter 1 -- Safety.
8.
Jack up both sides of the frame enough to  remove
rear wheels.
2
3
A.  Chock the front and rear of both front tires to pre-
vent the vehicle from moving.
1
2
B.  Support both sides of the frame with appropriate
jack stands positioned just  in front of the rear axle
tubes. This will  allow the transaxle  to be removed
from the vehicle.
3
Figure 24
3.
9.
fromthetransaxle(seeRearWheelandBrakeRemoval
in Chapter 7 -- Chassis).
Remove  both rear  wheels and  brake assemblies
1.
2.
Select lever assembly
Lock nut location
Shift cable
6
CAUTION
When removing engine tray, make sure hoist can
support the total weight of the engine, transaxle,
engine tray and other attached components. To-
tal weight is approximately 300 pounds (137 kg).
5
4
10.Attach
hoist to the engine tray to  allow engine and
transaxle to  be lowered  from the vehicle.  Make sure
hoist is attached  to hold the full weight  of the engine,
transaxle and tray.
3
1
11.
Remove  both flange  nuts (item  20), flat  washers
2
(item 18) and cap screws (item 19) that secure the en-
gine tray to the swing arm.
Figure 25
1.
2.
3.
Cap screw
4.
5.
6.
Isolation mount
Engine tray
Flange nut
12.Remove
ers (item 2) that secure the transaxle to the swing arm.
four (4) cap screws (item 3) and flat wash-
Flat washer
Swing arm bracket
Workman MD/MDX
Page 5 -- 17
Drive Train
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 178 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website