Toro 08160SL Workman MD MDX Service Manual

C. Remove four (4) socket head screws and flange
lock  nuts that  secure  the brake  assembly  to the
transaxle.
13.Bleed brakes (see Bleed Brake System in this sec-
tion).
D. Remove brake assembly from the transaxle.
CAUTION
Installation (Fig. 18)
After  servicing brake  system components,  al-
ways check the brakes in a wide open, level area
that is free of other persons and obstructions.
IMPORTANT: Parking  brake levers  must  be posi-
tioned above the transaxle mount. When positioned
correctly,brakeleverwillpointtowardtherearofthe
axle.
14.Check
brake operation.
1.
Position brake  assembly to  the transaxle.  Secure
Burnish Brake Shoes
backingplateofthebrakeassemblytothetransaxlewith
four  (4) socket  head  screws and  flanged  lock nuts.
Torque screws to 20 ft--lb (27 N--m).
Sintered metal linings may not provide maximum brake
stopping distance after brake shoes are replaced. It is
necessary to burnish new brake shoe linings.
2.
Positionnewbanjowasheroneachsideofbrakeline
fitting (Fig. 19). Insert banjo bolt into fitting and  thread
intowheelcylinder.Torquebanjoboltfrom    15to21ft--lb
IMPORTANT: Do not drive machine with the brakes
applied. The brake shoe linings will overheat.
(21
to 28 N--m).
IMPORTANT: During  brake burnishing  procedure,
do not allow the brakes to lock up. Allow brakes to
cool between applications.
3.
clevis pin and cotter pin.
Secure parking brake cable to the brake lever  with
IMPORTANT: Do  not  get antiseize  lubricant  onto
brake shoes.
1.
about 200 ft (60 m) intervals while traveling at 10 to 15
mph (16 to 24 KPH).
Drive machine while making 6 to 7 normal stops at
4.
Apply light coat of antiseize lubricant to the transaxle
shaft splines.
2
5.
washer and castle nut.
Secure wheel hub to  the shaft with washer, spring
1
3
6.
Torque castle nut 120 ft--lb (163 N--m). If slot in nut
does not align with hole in transaxle shaft, tighten nut to
alignnextslotwithholeinshaft.Castlenuttorqueshould
not exceed 200 ft--lb (271 N--m).
4
7.
8.
9.
Secure castle nut to shaft with cotter pin.
Slide brake drum onto wheel hub.
5
15
(21
to 21 ft--lb
to 28 N--m)
Position wheel assembly to the machine with valve
stem facing out and secure with five (5) lug nuts.
machine to ground.
Torque lug nuts in a crossing pattern from 45 to 65
10.Lower
Figure 19
11.
1.
2.
3.
Brake assembly
Wheel cylinder
Banjo washer
4.
5.
Banjo bolt
Brake line
ft--lb (62 to 88 N--m).
12.Check
parkingbrakeoperation.Adjustparkingbrake
if necessary (see Parking Brake Adjustment in the Ad-
justments section of this chapter).
Workman MD/MDX
Page 7 -- 29
Chassis
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 178 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website