Toro Single Stage Snow Blower Service Manual

ENGINE REMOVAL AND INSTALLATION
1965
- 1985 MODELS, ENGINE REMOVAL
Chain Drive Units:
A.   Remove the left side plate, chain guard and
chain.  To remove the chain, refer to "Chain
Replacement" on page 5 - 25.  Consult step 2.
Certain engine servicing procedures will require
removing the engine from your snowthrower.  The
following procedures are required for engine removal:
B.   Remove the crankshaft sprocket.  Refer to
"Crankshaft Sprocket Replacement (all
models)" on page 5 - 21.  Consult step 3.
1.
2.
Drain the gasoline from the fuel tank.  Refer to
“Draining The Fuel Tank” on page 2 - 5.
6.
Remove the switch terminal from the key switch if
your unit is so equipped.  Some 1980 model
S-200’s may have a terminal connection slightly
below the key switch.  It will be necessary to
separate the two terminals.
Remove all the mounting screws retaining the
upper shroud on 20” units.  On all 14” and 21”
snowthrowers, remove both the upper and lower
shrouds.  Be certain to install the gas cap after the
upper shroud is removed.
7.
8.
Slide the primer hose off the primer bulb fitting.
3.
4.
Disconnect the spark plug wire.
Remove the choke control.  Note:  Do not bend or
misform the carburetor choke control linkage.
Pull the rope from the starter and tie a small knot
in the starter rope before the starter housing
(Figure 34).  Allow the starter rope to retract until
the knot stops the starter rope at the starter
housing.  Next, remove the knot in the starter
handle and slide the handle off the starter rope.
9.
Remove the mounting screws retaining the lower
shroud on all 20” units.  On electric start 20” units,
remove screws retaining the switch and plug
assembly to the lower shroud.
10.
Using a hose clamp pliers or a needle nose pliers,
compress the fuel line clamp at the carburetor
fitting and slide the clamp down the fuel line hose
(Figure 35).  Remove the fuel line from the
carburetor.
Figure 34
0217-017
5.
Belt Drive Units:
A.   Remove the left side plate and belt.  Refer to
"Replacing Drive Belt" on page 5 - 1.  
Complete steps 1 through 4.
Figure 35
0217-018
B.   Remove the crankshaft pulley.  Refer to
"Replacing Drive Belt" on page 5 - 1.  
Complete step 2.
Single Stage Snowthrower Service Manual
4 - 1
Product Specification
CategoriesSnow Blower Manuals, Toro Snow Blower
Tags, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 124 pages
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Snow Blower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(3 votes, average: 4.67 out of 5)
Lawn and Garden readers have rated Toro Single Stage Snow Blower Service Manual 4.7 out of 5.0 based on 3 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro Single Stage Snow Blower Service Manual SKU UPC Model
Frank Husted on Mar 26, 2018. Toro CCR2000 manual

EXCELLENT . Hard to find manual and very detailed . Only downside is the pics and wording in pics are backwards , but I can deal with that


William Scheuerell on Feb 11, 2018. Complete, except...

The manual provides detailed step-by-step instructions for engine removal and installation but there is nothing in it about repair of the recoil starter. The engine removal instructions will be helpful because the starter is buried behind the fuel tank and engine support bracket. I think my problem is a sticking starter dog but getting to it will be a major project.


Mark on Dec 23, 2016.

manual downloak for toro snwo thorower, downlod manual for toro


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website