Toro 08161SL Service Manual Model 30412 Groundsmaster 4000 D Preface Publication

NOTE:  Theplanetarywheeldriveassemblycanbeser-
vicedwiththeplanetaryinstalledtomachine(seePlane-
tary  Wheel  Drive  Service  in  this  section). Use  the
following  procedure to  remove  and  install planetary
wheel drive assembly from machine.
2.  Install brake assembly (see Brake Assembly Instal-
lation in this section).
3.
Install hydraulic wheel motor (see Front Wheel Mo-
tors in the Service and Repairs section of Chapter 4 --
Hydraulic System).
Removal (Fig. 6)
4.
Install wheel assembly.
1.
decks, stop  engine and remove  key from the ignition
switch.
Park  machine  on  a  level  surface,  lower  cutting
WARNING
2.
Drainoilfromplanetary  wheeldrive/brake assembly.
Failure to maintain proper wheel lug nut torque
could result in failure or loss of wheel and may
result in personal injury.
CAUTION
5.
from 85 to 100 ft--lb (115 to 135 N--m).
Lower machine  from jack stands.  Torque lug nuts
When removing front  wheel, use correct jacks
and supports. Make sure machine isparked on a
solid,  level surface  such as  a  concrete floor.
Prior  to raising  machine, remove  any  attach-
ments that may interfere with the safe and prop-
erraisingof  themachine. Alwayschock orblock
wheels. Use jack  stands to support  the raised
machine.  If the  machine is  not  properly sup-
ported by jack stands, the machine may move or
fall, which may result in personal injury.
6.
Make sure drain plug is installed in bottom of brake
assembly (Fig. 7). Fill planetary wheel  drive/brake as-
sembly  with  SAE  85W--140  gear  lube.  Capacity is
approximately 16 fl. oz. (0.47 liters) per wheel.
7.
eration.
Check and adjust brake cables for proper brake op-
1
3.
Chock rear wheels and jack up front of machine (see
JackingInstructions inChapter1  -- Safety).Supportma-
chine with jack stands.
4.
5.
Remove front wheel assembly.
2
Remove hydraulic  wheel motor  (see Front  Wheel
Motors in the Service and Repairs section of Chapter 4
--
Hydraulic System).
6.
Remove brake assembly (see Brake Assembly Re-
moval in this section).
3
7.
Supportplanetaryassemblytopreventitfromfalling.
Loosen and  remove flange  head screws  that secure
planetary assembly  to  frame. Remove  planetary as-
sembly from machine.
Figure 7
1.
2.
Brake housing
Check plug
3.
Drain plug
Installation (Fig. 6)
1.
flange head  screws  that secure  planetary assembly.
Position  planetary  assembly  to   machine.  Install
Torque screws in a crossing pattern from 75 to 85 ft--lb
(101
to 115 N--m).
Groundsmaster 4000--D
Page 6 -- 9
Axles, Planetaries and Brakes
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website