Service and Repairs
General Precautions for Removing and Installing Hydraulic System Components
Before Repair or Replacement of Components
Before removing any parts from the hydraulic sys-
tem, park machine on a level surface, apply parking
brake, lower cutting decks or attachments and stop en-
gine. Remove key from the ignition switch.
After Repair or Replacement of Components
1.
1. Checkoillevelinthehydraulic reservoir andaddcor-
rect oil if necessary. Drain and refill hydraulic system
reservoir and change oil filter if component failure was
severe or system is contaminated (see Flush Hydraulic
System in this section).
2.
Clean machine before disconnecting, removing or
disassembling any hydraulic components. Make sure
hydraulic components, hoses connections and fittings
are cleaned thoroughly. Always keep in mind the need
for cleanliness when working on hydraulic equipment.
2. Lubricate O--rings and seals with clean hydraulic oil
before installing hydraulic components.
3.
Make sure caps or plugs are removed from the hy-
draulic tubes, hydraulic fittings and components before
reconnecting.
CAUTION
4.
Use proper tightening methods when installing hy-
draulic hoses and fittings (see Hydraulic Fitting Installa-
tion in the General Information section of this chapter).
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil.
5. After repairs, check control linkages or cables for
proper adjustment, binding or broken parts.
3.
tings and components left open or exposed to prevent
contamination.
Putcapsorplugsonanyhydrauliclines,hydraulicfit-
6.
After disconnecting or replacing any hydraulic com-
ponents, operate machine functions slowly until air is
out ofsystem (see Charge Hydraulic System in this sec-
tion).
4.
Put labels on disconnected hydraulic lines and
hosesforproperinstallationafterrepairsarecompleted.
7.
Checkforhydraulicoilleaks.Shutoffengineandcor-
rectleaksifnecessary.Checkoillevelinhydraulicreser-
voir and add correct oil if necessary.
5.
Note the position of hydraulic fittings (especially el-
bow fittings) on hydraulic components before removal.
Markpartsifnecessarytomakesuretheywillbealigned
properly when installing hydraulic hoses and tubes.
Check Hydraulic Lines and Hoses
IMPORTANT: Checkhydraulic linesandhosesdaily
for leaks, kinked lines, loose mounting supports,
wear, loose fittings or any hose deterioration. Make
all necessary repairs before operating.
WARNING
Keep body and hands away from pin hole leaks
or nozzles that eject hydraulic fluid under high
pressure. Use paper or cardboard, not hands, to
search for leaks. Hydraulic fluid escaping under
pressure can have sufficient force to penetrate
the skin and cause serious injury. If fluid is in-
jected into the skin, it must be surgically re-
moved within a few hours by a doctor familiar
withthistypeofinjury.Gangrenemayresultfrom
such an injury.
Groundsmaster 4000--D
Page 4 -- 61
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 30412, Toro Groundsmaster 4000 D |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)