NOTE: Theplanetarywheeldriveassemblycanbeser-
viced with the planetary installed to machine. If the
spindle(item1)needstoberemovedfrommachine,see
Planetary Wheel Drive Assembly Removal in this sec-
tion.
3
4
19
20
7
1
24
2
8
11
21
12
Disassembly (Figs. 8 and 9)
14
1.
chine:
If planetary wheel drive assembly is installed on ma-
15
17
A. Park machine on a level surface, lower cutting
decks, stop engine and remove key from the ignition
switch.
16
13
B. Drain oil from planetary wheel drive/brake as-
sembly.
C. Chock rear wheels and jack up front of machine
(see Jacking Instructions in Chapter 1 -- Safety).
Support machine with jack stands.
22
9
10
6
5
23
21
18
D. Remove front wheel assembly.
Figure 9
Assembly (Figs. 8 and 9)
2.
3.
thrust washer (item 16) usually remain in end cap bore
and should be removed for cleaning and inspection.
Remove retaining ring (item 12).
Remove endcap(item14).Thrustplug(item15)and
1. Thoroughlycleanpartsinsolventanddrycompletely
after cleaning. Inspect parts for damage or excessive
wear and replace as necessary.
4.
5.
6.
Remove drive shaft assembly (items 17).
Remove carrier assembly (item 18).
NOTE: Use new seal and shim kits when assembling
planetary wheel drive.
If wheel stud (item 5) removal is necessary, use
2.
If spindle and housing were separated:
press to extract stud(s) from housing.
A. Press bearing cups (items 4 and 7) into housing
(item 6). Cups should be pressed fully to shoulder of
the housing bore.
NOTE: Steps 6 through 10 are necessary only if in-
specting or replacing bearings and/or seals.
IMPORTANT: Do not reuse retaining ring (item 10)
after it has been removed.
B. Set inner bearing cone (item 3) into bearing cup
(item 4) that is installed in housing.
7.
(item 9). Discard retaining ring.
Remove retaining ring (item 10) and thrust washer
C. Make sure that seal bore in housing is thoroughly
cleaned. If OD of seal (item 24) is not rubber or does
not have a sealant coating, apply light coating of sili-
cone sealant to seal bore in housing. Install seal into
housing so it is flush with housing face. Lightly
grease seal lips.
8.
move outer bearing cone (item 8).
Remove housing (item 6) from spindle (item 1). Re-
9.
21
Remove and discard all seals and O--rings (items 2,
and 24).
D. Pack boot seal (item 2) with grease and install on
housing.
10.If
bearings will be replaced, remove inner bearing
cone (item 3) from housing. Remove bearing cups
(items 4 and 7) from housing.
E. If ring gear was removed from housing, place
dowel pins (item 23) in housing. Secure ring gear to
housingwithlockwashers(item20)andsockethead
screws (item 19).Torquesocket head screws to 9ft--
lb (12 N--m).
11.
If necessary, remove socket head screws (item 19)
with lock washers (item 20) that secure ring gear (item
tohousing. Removeringgearandtwo(2)dowelpins
11)
(item 23) from housing.
Groundsmaster 4000--D
Page 6 -- 11
Axles, Planetaries and Brakes
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Groundsmaster 30412, Toro Groundsmaster 4000 D |
Download File |
|
Document Type | Catalog |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)