Toro 08161SL Service Manual Model 30412 Groundsmaster 4000 D Preface Publication

Removal (Figs. 10 and 11)
Park  machine  on  a  level  surface,  lower  cutting
decks, stop  engine, apply parking  brake and remove
key from the ignition switch.
3.  Slowly rotate cutting blades to verify that blades do
not contact any deck components.
1.
4.  Install drive belt to  spindle pulleys and idler pulley.
Adjustdrivebelttension(seeIdlerAssembly    Installation
in this section).
2.
Remove covers from cutting deck to allow access to
blade spindle.
5.  If drive spindle was removed, install hydraulic motor
to cutting deck (see Cutting Deck  Motor Installation in
the Service and Repairs Section of Chapter 4 -- Hydrau-
lic Systems).
3.
If drive spindle is to  be serviced, remove hydraulic
motor from cutting  deck (see Cutting Deck Motor  Re-
moval in the Service and Repairs Section of Chapter 4
--
Hydraulic  Systems).   Position  motor   away  from
6.  Install covers to cutting deck.
spindle.
4.
(see Idler Assembly Removal in this section). Remove
drive belt from spindle to be serviced.
Loosen idler assembly to release drive belt tension
6
3
4
5.
gine and remove key from the ignition switch. Latch or
block up the cutting deck so it cannot fall accidentally.
Start the engine and raise the cutting deck. Stop en-
1
6.
Remove cutting blade, anti--scalp cup and blade bolt
from spindle to be serviced.
2
7.
Remove spindle housing assembly from deck.
A.  For driven spindle assemblies, remove eight (8)
flange  head screws  with  flange nuts  that  secure
spindle to deck.
7
5
8
B.  Fordrivespindleassemblies,removefour(4)cap
screws with  washers that  secure spindle  and hy-
draulic motor mount to deck. Remove motor mount.
Then, remove four (4) flange head screws with flan-
ge nuts that secure spindle to deck.
10
9
88
to 108 ft--lb
(120 to 146 N--m)
11
Figure 11
C. Lift spindle assembly from deck.
1.
2.
3.
4.
5.
6.
Deck (RH shown)
Driven spindle
Drive spindle
Flange head screw
Flange nut
7.
8.
9.
10. Anti--scalp cup
11. Blade bolt
Washer
Cap screw
Blade
Installation (Figs. 10 and 11)
Position spindle on cutting deck noting orientation of
greasefitting(Fig.10).Securespindleassembly    todeck
with removed fasteners.
1.
Drive belt
2.
Install cutting blade, anti--scalp cup and blade bolt to
spindle. Tighten blade bolt from 88 to 108 ft--lb (120 to
N--m).
146
Groundsmaster 4000--D
Page 8 -- 13
Cutting Decks
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags,
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 298 pages
Document TypeCatalog
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website