Toro 05145SL Rev B Groundsmaster 3505 D Service Manual

Disassembly (Fig. 66)
Removeoilfromliftcylinderintoadrainpanbyslowly
pumping the cylinder shaft. Plug  both ports and clean
the outside of the cylinder.
IMPORTANT: Prevent  damage when clamping  the
hydraulic cylinder into a vise;  clamp on the clevis
ONLY.
1.
4.  Mount barrel in a vise.
IMPORTANT: Prevent  damage when clamping  the
hydraulic cylinder into a vise;  clamp on the clevis
ONLY.
5.  Coat all internal parts with  a light coat of clean hy-
draulic oil. Slide piston, shaft  and head assembly into
the barrel being careful not to damage the seals.
2.
with a spanner wrench.
Mount lift cylinder in a vise. Remove internal  collar
6.  Secure head in the barrel with internal collar using a
spanner wrench. Tighten collar until snug and the outer
end of the collar is flush with end of the barrel.
3.
Remove plugs from  ports. Extract shaft, head and
piston by carefully twisting and pulling on the shaft.
7.  Ifcleviswasremovedfromcylindershaft,fullyretract
cylinder shaft and thread jam nut and clevis onto shaft.
Adjust center to  center length to  dimension shown in
Figure 67 before tightening jam nut.
IMPORTANT: Do  not clamp  vise jaws  against the
shaft surface. Clamp on the clevis ONLY.
4.
vis of the shaft.  Remove lock nut and piston  from the
shaft. Slide head off the shaft.
Mountshaftsecurelyinavisebyclampingonthecle-
10.125”
to 10.500”
(25.72
to 26.67 cm)
5.
Remove Uni--ring  and o--ring from the  piston. Re-
move o--ring, back--up ring, rod seal and dust seal from
the head.
Assembly (Fig. 66)
1.
2.
Make sure all parts are clean before reassembly.
Coat new o--rings, Uni--ring, rod seal, back--up ring
Figure 67
and dust seal with clean hydraulic oil.
A.  Install Uni--ring and o--ring to the piston.
B.  Install dust seal, o--ring, back--up ring  and dust
seal to the head.
IMPORTANT: Do  not clamp  vise jaws  against the
shaft surface. Clamp on the clevis ONLY.
3.
Mountshaftsecurelyinavisebyclampingonthecle-
vis of the shaft.
A.  Coat shaft with clean hydraulic oil.
B.  Slide head onto  the shaft. Install rod  seal onto
shaft and into head.
C. Install piston and lock nut onto the shaft. Torque
lock nut from 24 to 30 ft--lb (33 to 41 N--m).
D. Remove shaft from the vise.
Groundsmaster 3505--D
Page 4 -- 101
Hydraulic System
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 210 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website