Toro 05145SL Rev B Groundsmaster 3505 D Service Manual

Rear Roller Service (Greasable Bearings with Bearing Nut)
Disassembly (Fig. 7)
2
50
to 60 ft--lb
1.
shaft.
Remove bearing  lock nut  from each  end of  roller
3
(68 to 81 N--m)
4
5
2.
Loosely secure  roller assembly in  bench vise and
lightly tap one end of  roller shaft until outer seals and
bearing are removed from opposite end  of roller tube.
Remove second setofouter seals andbearing fromroll-
er tube by  tapping on opposite end  of shaft. Remove
shaft from roller tube.
6
7
1
2
3
4
5
3.
tube taking care to not damage tube surfaces.
Carefully remove inner seal from both ends of roller
6
4.
5.
Discard removed seals and bearings.
Loctite #242
Clean roller shaft andallsurfaces on theinside ofthe
roller tube.  Inspect components for  wear or damage.
Also, carefully inspect  seating surface and threads  of
bearing lock nuts. Replace all damaged components.
Assembly (Fig. 7)
7
1
Figure 7
1.
Install inner seals into  roller tube making sure that
seal lip (and garter spring) faces end of tube. Use inner
sealtool(seeSpecialTools)andsoftfacehammertoful-
ly seat  seals against roller  shoulder (Fig. 8).  Apply a
smallamountofgreasearoundthelipofbothinnerseals
after installation.
1.
2.
3.
4.
Roller tube
Roller shaft
Inner seal
Bearing
5.
6.
7.
Outer seal
Bearing lock nut
Set screw
1
2
3
IMPORTANT: During assembly process, frequently
check that bearings rotate freely and do not bind. If
any binding  is detected,  consider component  re-
moval and reinstallation.
2.
Install new bearing and outer seals into one end of
roller tube:
A.  Position anew bearing into one end ofrollertube.
Use bearing/outer seal tool (see Special Tools) with
asoftfacehammer  tofullyseatbearing   againstroller
shoulder (Fig.  9). After  bearing installation,  make
sure that it rotates freely with no binding.
Figure 8
3.
1.
2.
Roller tube
Inner seal
Inner seal tool
1
2
3
B.  Apply a small amount of grease around the lip of
both outer seals.
4
C. Install first outer seal into roller tube making sure
that seal lip  (and garter spring) faces  end of tube.
Use bearing/outer seal tool (see Special Tools) and
soft face hammer  to lightly seat seal against  roller
shoulder (Fig. 10). Make sure that bearing still freely
rotates after seal installation.
Figure 9
4.
5.
D. Using  the  same process,  install  second outer
sealmakingsuretonotcrushtheinstalledouterseal.
Again, make sure that bearing still freely rotates.
1.
2.
3.
Roller tube
Inner seal
Bearing
Washer
Bearing/outer seal tool
Cutting Units
Page 7 -- 10   Rev. A
Groundsmaster 3505--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 210 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website