Toro 05145SL Rev B Groundsmaster 3505 D Service Manual

16.Separate
engine as follows:
hydrostat and pump mount plate from the
1
2
A.  Remove traction belt  from the  engine flywheel
and hydrostat pulleys (see Traction Unit Operator’s
Manual).
4
6
B.  Support hydraulic pump assembly  to prevent it
from falling during removal.
3
C. Removefive(5)capscrews,four(4)washersand
five(5)spacerssecuringthepumpmountplatetothe
engine (Fig. 12  and 13). Note location  of spacers,
washers and cap screws during removal.
6
5
D. Remove four (4) cap screws (item 12) and hard-
ened washers  (item 11)  securing the right  engine
mounting bracket to the engine.
Figure 12
4.
5.
6.
1.
2.
3.
Cap screw (10 mm)
Short spacer
Torsion spring
Pump mount plate
Cap screw (8 mm)
Long spacer (4 used)
E.  Remove  hydrostat,   pump   mount  plate   and
mounting brackets from engine.
17.As
necessary, remove engine mounts (item 3), front
engine  mounting  bracket (item  13),  throttle  support
bracket (item 42) andleftengine mounting bracket(item
14).
1
Installation (Fig. 7)
1.
If removed, install engine mounts (item 3), front en-
ginemountingbracket(item13),throttlesupportbracket
(item 42) and  left engine mounting  bracket (item 14).
Also,  make  sure that  all  switches  and  sensors are
installed on engine.
3
6
1
2.
Install hydrostat,  pump mount plate and  mounting
4
brackets to the engine as follows:
5
2
3
A.  Positionhydrostat,pumpmountplateandmount-
ing brackets to engine.
Figure 13
1.
2.
3.
Long spacer (4 used)
Flat washer (3 used)
8 mm cap screw (4 used)
4.
5.
6.
Hardened washer
10 mm cap screw
Short spacer
B.  Secure right engine mounting bracket  (with hy-
drostat attached) to  the engine with  four (4) hard-
ened washers and cap screws.
CAUTION
NOTE:  To prevent the torsion spring from binding,
do not  install  flat washer  on cap  screw  near the
spring.
One person should operate  lift or hoist while a
second person  guides the engine  into the ma-
chine.
C. Using locations noted during engine removal, se-
cure pump mount  plate to the  engine with five (5)
spacers, four (4)  washers and five (5)  cap screws
(Fig. 12 and 13).
IMPORTANT: Make sure not to damage the engine,
fuel or hydraulic  lines, electrical harness or  other
parts while installing the engine.
D. Install traction belt to the engine flywheel and hy-
drostat pulleys (see Traction Unit Operator’s Manu-
al).
4.
Carefully lower engine into the machine.
5.
ing brackets with cap screws, washers and flange nuts.
Securethree(3)enginemountstotheenginemount-
3.
tabs (Fig. 9 and 10).
Connect hoist or lift to the front and  rear engine lift
Kubota Diesel Engine
Page 3 -- 14
Groundsmaster 3505--D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 210 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(0 votes, average: 0 out of 5)

Submit your review (optional)
(will not be displayed)
* Required Field

Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website