Removal (Fig 57)
Park machine on a level surface, lower cutting deck,
stop engine, engage parking brake and remove key
from the ignition switch.
Installation (Fig 57)
1.
1. If fittings were removed from gear pump, lubricate
and place new O--rings onto fittings. Install fittings into
port openings using marks made during the removal
process to properly orientate fittings. Tighten fittings
(see Hydraulic Fitting Installation in the General Infor-
mation section of this chapter).
2.
pump from the underside of the machine.
Raise and support machine to gain access to gear
3.
4.
pump removal, thoroughly clean exterior of pump and
fittings.
Drain the hydraulic reservoir.
A. If90ohydraulic suction fitting(item8)andstraight
fitting (item9)were removed fromgearpump,torque
fittings from 103 to 118 ft--lb (140 to 160 N--m).
To prevent contamination of hydraulic system during
2.
3.
Slide coupler onto the piston pump output shaft.
Lubricate new O--rings(item 13)with cleanhydraulic
5.
Installing Hydraulic System Components at the begin-
ning of this section.
Read the General Precautions for Removing and
oil. Position O--rings and spacer to gear pump.
4.
screws (item 19).
Apply Loctite #242 (or equivalent) to threads of cap
6.
caps or plugs on open hydraulic lines and fittings. Label
disconnected hydraulic lines for proper installation.
Disconnect hydraulic lines from gear pump and put
5. Align gear teeth and slide gear pump input shaft into
coupler. Secure gear pump to piston pump with two (2)
cap screws and washers. Torque cap screws from 79 to
7.
ling.
Support gear pump assembly to prevent it from fal-
84
ft--lb (108 to 113 N--m).
8.
Removetwo(2)capscrewsandwashersthatsecure
6.
Remove caps orplugs fromallhydraulic lines andfit-
gear pump to piston pump. Remove gear pump, cou-
pler, spacer and O--rings from machine through the seat
opening.
tings.Usinglabelsplacedduringpumpremoval,proper-
ly install hydraulic lines to gear pump (see Hydraulic
Hose and Tube Installation in the General Information
section of this chapter).
9.
If hydraulic fittings are to be removed from gear
pump, mark fitting orientation to allow correct assembly.
Remove fittings from pump and discard O--rings.
7.
8.
Lower machine to ground.
Replace hydraulic filter and fill hydraulic reservoir
with new hydraulic oil.
9.
Disconnect engine run solenoid electrical connector
to prevent engine from starting. Prime the hydraulic
pumpbyturningtheignitionkeyswitchtostartandcrank
the engine for ten (10) seconds. Wait fifteen (15) sec-
onds to allow the starter motor to cool and then repeat
cranking procedure again.
10.Connect
engine run solenoid electrical connector,
start the engine and check for proper operation.
11.
Properly fill hydraulic system (see Charge Hydraulic
System in this section).
12.Stop
engine and check for hydraulic oil leaks. Check
hydraulic reservoir oil level.
Groundsmaster 4100--D/4110--D
Page 4 -- 83
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 10177SL, Toro Groundsmaster 30447, Toro Groundsmaster 30449, Toro Groundsmaster 4100, Toro Groundsmaster 4110 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)