Removal (Fig. 104)
Park machine on a level surface, lower cutting deck,
stop engine, engage parking brake and remove key
from the ignition switch.
Installation (Fig. 104)
1.
1. If removed, install spherical bearings into lift cylinder
clevis ends.
A. On shaft clevis, press spherical bearing into cle-
vis and secure with retaining ring.
2.
Read the General Precautions for Removing and
Installing Hydraulic System Components at the begin-
ning of this section.
B. On barrel clevis, install spherical bearing on ta-
pered stud and secure with flange nut. Torqueflange
nut from 30 to 40 ft--lb (41 to 54 N--m). Install stud
with spherical bearing into clevis and secure with re-
taining ring.
WARNING
2.
stud and mounting boss on deck.
Thoroughly clean tapered surfaces of lift cylinder
Make sure that cutting deck (including wing
decks) is fully lowered before loosening hydrau-
lic lines fromwing deck lift cylinders. If decks are
notfullyloweredashydrauliclinesareloosened,
deck may drop unexpectedly.
3. Position lift cylinder to cutting deck. Insert tapered
stud into deck mounting boss. Secure stud with flat
washer and lock nut. Torque flange nut from 160 to 180
ft--lb (217 to 244 N--m).
3.
Remove deck covers as needed to allow access to
lift cylinder hoses and fasteners.
4.
Insert cap screw from the front of the deck through
the deck brackets and cylinder shaft clevis. Secure cap
screw with lock nut. Torque lock nut from 160 to 180 ft--
lb (217 to 244 N--m).
4.
lift cylinder removal, thoroughly clean exterior of cylin-
der and hose fittings.
To prevent contamination of hydraulic system during
5.
Remove caps and plugs from fittings and hydraulic
NOTE: Toeaseinstallation,labelthehydraulichosesto
show their correct position on the lift cylinder.
hoses. Using labels placed during cylinder removal,
properly attach hydraulic hoses to lift cylinder (see Hy-
draulic Hose and Tube Installation in the General Infor-
mation section of this chapter).
5.
caps or plugs on open hydraulic hoses and fittings. La-
beldisconnected hydraulic hosesforproperinstallation.
Disconnect hydraulic hoses from lift cylinder and put
6.
7.
8.
verify that hydraulic hoses and fittings are not contacted
by anything.
Install all removed deck covers.
6.
Remove cap screw and lock nut that secure the lift
Fill reservoir with hydraulic fluid as required.
After assembly is completed, operate lift cylinder to
cylinder clevis to the wing deck.
7.
stud on the barrel end of the lift cylinder.
Remove lock nut and flat washer from the tapered
8.
9.
Remove lift cylinder from deck assembly.
Remove spherical bearings from lift cylinder clevis
ends, if required.
A. On shaft clevis, remove retaining ring and then
press spherical bearing from clevis.
B. On barrel clevis, remove retaining ring and then
press tapered stud with spherical bearing and flange
nut from clevis. Remove flange nut and then spheri-
cal bearing from stud.
Groundsmaster 4100--D/4110--D
Page 4 -- 145
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 10177SL, Toro Groundsmaster 30447, Toro Groundsmaster 30449, Toro Groundsmaster 4100, Toro Groundsmaster 4110 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)