Removal (Fig. 1)
Park machine on a level surface, lower cutting deck,
25
24
1.
6
23
stop engine and remove key from the ignition switch.
21
22
2.
Drainoilfromplanetary wheeldrive/brake assembly.
5
1
CAUTION
2
3
9
20
6
4
When removing front wheel, use correct jacks
and supports. Make sure machine isparked on a
solid, level surface such as a concrete floor.
Prior to raising machine, remove any attach-
ments that may interfere with the safe and prop-
erraisingof themachine. Alwayschock orblock
wheels. Use jack stands to support the raised
machine. If the machine is not properly sup-
ported by jack stands, the machine may move or
fall, which may result in personal injury.
7
19
21
18
22
17
8
11 10
16
9
12
13
14
15
3.
Chock rear wheels and jack up front of machine (see
JackingInstructions inChapter1 -- Safety).Supportma-
chine with jack stands.
Figure 2
4.
moval (see Operator’s Manual).
Tilt the cutting deck upright to allow front wheel re-
1.
2.
3.
4.
5.
6.
7.
8.
9.
Brake lever
14. Compression spring
15. Brake link
16. Brake assembly
17. Jam nut
18. Spring plate
19. Jam nut
20. Brake cable
21. Flat washer
22. Cotter pin
Thrust washer (2 used)
Flat washer
Lock nut
5.
6.
Remove front wheel assembly.
Bushing
Clevis pin
Remove hydraulic wheel motor (see Front Wheel
Lock nut
Cap screw
Brake link
Motors in the Service and Repairs section of Chapter 4
--
Hydraulic System).
10. Rod end (LH thread)
23. Screw (2 used)
24. Cable bracket
25. Frame rail
11.
12.
13.
Jam nut (LH thread)
Hex link
7.
frame bracket and pull rod on brake assembly (Fig. 2).
Disconnect brake link assembly from brake lever,
Flanged spacer
8.
9.
Support brake assembly to prevent it from falling.
Remove flange head cap screws (item 9) securing
3
brake assembly to frame.
10.Remove
brake assembly from machine. Be careful
to not drop splined brake shaft (item 3) as brake assem-
bly is removed.
11.
Remove splined brake shaft from brake assembly.
2
1
12.Remove
and discard gasket (item 11). Make sure
that all gasket material is removed from both brake and
planetary assemblies.
13.Complete
spection and Repair in this section).
brake inspection and repair (see Brake In-
Figure 3
1.
2.
Brake housing
Check plug
3.
Brake link assembly
Groundsmaster 4100--D/4110--D
Page 6 -- 5
Axles, Planetaries and Brakes
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 10177SL, Toro Groundsmaster 30447, Toro Groundsmaster 30449, Toro Groundsmaster 4100, Toro Groundsmaster 4110 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)