8.
corner of 4WD hydraulic manifold to rear frame mount.
Remove cap screw and flange nut that secures front
1
2
9.
If required, remove tie rod ends from steering arms
3
4
on rear axle (Fig. 13). Remove the cotter pins and castle
nuts from the tie rod ball joints. Use a ball joint fork and
remove the tie rod ends from the axle steering arms.
10.Support
rear axle to prevent it from falling. Remove
six (6) cap screws, flat washers and flange nuts that se-
cure rear frame mount to equipment frame. Lower rear
axle and rear frame mount from machine.
5
11.
Remove lock nut and washer from pivot pin that at-
taches rear axle to rear frame mount. Remove washer
head screw that secures flange of pivot pin to frame
mount (Fig. 14).
Figure 12
12.Remove
rear axle. Note location of thrust washers on both ends
of axle mounting boss.
pivot pin. Separate rear frame mount from
1.
2.
3.
Hydraulic hose
Hydraulic hose
Hydraulic tube
4.
5.
Hydraulic tube
Rear frame mount
Installation (Fig. 11)
4
5
3
2
1.
Position rear frame mount to axle. Install thrust
washers between axle boss and frame mount. The thin-
ner thrust washer should be installed on the hydraulic
motor end of the axle (toward the rear of the machine).
With washers installed, there should be from 0.002 to
1
0.020
frame mount and axle mounting boss. Add thrust wash-
ers if needed to adjust clearance.
in. (0.05 mm to 0.51 mm) clearance between rear
6
2.
Install axle pivot pin to secure axle to rear frame
mount. Tighten lock nut and then loosen it slightly to al-
low the axle pin to pivot freely. Secure pivot pin to frame
mount with washer head screw (Fig. 14).
Figure 13
1.
2.
3.
Tie rod
Dust cover
Cotter pin
4.
5.
6.
Castle nut
3.
Tighten ball joint castle nuts and install new cotter pins.
If removed, install the tie rod to rear axle (Fig. 13).
Tie rod end
Steering arm (LH)
4.
jack. Raise assembly to machine frame and align
mounting holes of rear mount and machine frame.
Position axle and rear mount under machine with a
2
1
5.
Secure rear mount to frame with six (6) cap screws,
flat washers and flange nuts.
6.
corner of 4WD hydraulic manifold to rear frame mount.
Install cap screw and flange nut that secures front
7.
mount with washers and bulkhead lock nuts (Fig. 12).
Install steering cylinder hoses to hydraulic tubes.
Attachsteeringcylinderhydraulictubestorearframe
Figure 14
1.
Pivot pin
2.
Washer head screw
Groundsmaster 4100--D/4110--D
Page 6 -- 17
Axles, Planetaries and Brakes
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 10177SL, Toro Groundsmaster 30447, Toro Groundsmaster 30449, Toro Groundsmaster 4100, Toro Groundsmaster 4110 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)