4.
brackets.
Position upper end of links to center cutting deck
10.Fully raise wing deck, stop engine and remove key
from the ignition switch. Secure flex shield to wing deck
with shield strap and three (3) washer head screws.
Lower wing deck.
5.
deck.Whileinstalling pivot pins to center deck andlinks,
insert spacers and washers as follows:
Alignupperendoflinkswithmountingholesincenter
11.Lower wing deck and inspect deck latch assembly to
insure that front link is locked when the wing deck is in
the lowered position. There should be agap from 0.060”
to 0.090” (1.5 to2.2 mm)between thearm latchactuator
and the latch pivot (Fig. 8). If gap is incorrect, adjust link
position by repositioning the location of the hardened
spacers (item 42) and thrust washers (item 6). At a mini-
mum,theremustbeone(1)hardenedspacerpositioned
to the rear of the front link.
A. Place one (1) hardened spacer (item 42) on each
side of the front link. Use two (2) thrust washers on
rear side of assembly so that link is snug between
deck brackets. Additional thrust washers should be
installed, if necessary, to remove excess clearance.
B. Place one (1) thrust washer (item 6) on each side
of rear link. Clearance between rear link and deck
bracket is acceptable.
12.Lubricate
ponents.
grease fittings on cutting deckand liftcom-
6.
Secure pins with carriage screw and flange head
screw.
13.Check
distance between inner deck blade on wing
deck and outer deck blade on center deck. Distance be-
tween blades should be 0.380” to 0.620” (9.7 to 15.7
mm) (Fig. 9). If blade distance is incorrect, loosen hex
jam nut (item 32) on rear link assembly and adjust cap
screw (item 31). Tighten jam nut when blade distance is
correct.
7.
Cap screw on rear link uses a flat washer (item 28). Cap
screw on front link also secures hose guide (item 38).
Install cap screw (item 29) to pivot pin on both links.
8.
cylinder with cap screw and lock nut.
Position lift cylinder to the wing deck (Fig. 7). Secure
14.Check
if necessary (see Wing Deck Position Switches in the
Adjustments section of Chapter 5 -- Electrical System).
operation ofwing deck position switch. Adjust
9.
Deck Motor Installation in the Service and Repairs Sec-
tion of Chapter 4 -- Hydraulic System).
Install hydraulic motor to cutting deck (see Cutting
15.Secure
switch shield (item 50) to center deck.
Cutting Deck
Page 8 -- 12
Groundsmaster 4100--D/4110--D
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 10177SL, Toro Groundsmaster 30447, Toro Groundsmaster 30449, Toro Groundsmaster 4100, Toro Groundsmaster 4110 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)