Relieving Hydraulic System Pressure
Before disconnecting or performing any work on the hy-
draulic system, all pressure in the hydraulic system
mustberelieved.Parkmachineonalevelsurface,lower
cutting deck fully, stop engine and engage parking
brake. Wait for all moving parts to come to a complete
stop.
To relieve hydraulic pressure in lift circuit, start engine
and fully lower the cutting deck (including the wing
decks).TurnkeyswitchtoOFFandremovekeyfromthe
ignition switch.
System pressure in mow circuit is relieved when the
PTO switch is disengaged.
To relieve hydraulic pressure in traction circuit, move
traction pedal to both forward and reverse directions. To
relieve hydraulic pressure in steering circuit, rotate
steering wheel in both directions.
Traction Circuit Component Failure
The traction circuit on Groundsmaster 4100--D and
Once the Toro high flow hydraulic filter kit has been
placed in the circuit, raise and support the machine with
all wheels off the ground. Then, operate the traction cir-
cuit to allow oil flow throughout the circuit. The filter will
remove contamination from the traction circuit during
operation. Because the Toro high flow filter is bi--direc-
tional, thetraction circuitcan beoperated inboth thefor-
ward and reverse direction. The filter should be
removed from the machine after contamination has
been removed from the traction circuit. See Filtering
Closed--LoopTractionCircuitintheServiceandRepairs
section of this chapter for additional information on us-
ing the Toro high flow hydraulic filter.
4110--D
machines is a closed loop system that includes
the piston (traction) pump, two (2) front wheel motors
and the rear axle motor. If a component in the traction
circuit should fail, debris and contamination from the
failed component will circulate throughout the traction
circuit. This contamination can damage other compo-
nents in the circuit so it must be removed to prevent
additional component failure.
The recommended method of removing traction circuit
contamination would be to temporarily install the Toro
high flow hydraulic filter (see Special Tools in this chap-
ter) into the circuit. This filter should be used when con-
necting hydraulic test gauges in order to test traction
circuitcomponents orafterreplacing afailedtractioncir-
cuit component (e.g. traction (piston) pump or wheel
motor). The filter will ensure that contaminates are re-
movedfromtheclosedloopandthus,donotcauseaddi-
tional component damage.
Thealternative tousingtheTorohighflowhydraulicfilter
kit after a traction circuit component failure would be to
disassemble, drain and thoroughly clean all compo-
nents, tubes and hoses in the traction circuit. If any de-
bris remains in the traction circuit and the machine is
operated,thedebriscancauseadditionalcircuitcompo-
nent failure.
Hydraulic System
Page 4 -- 4
Groundsmaster 4100--D/4110--D
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 10177SL, Toro Groundsmaster 30447, Toro Groundsmaster 30449, Toro Groundsmaster 4100, Toro Groundsmaster 4110 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)