Removal (Fig. 7)
Park machine on a level surface, lower cutting deck,
stop engine, apply parking brake and remove key from
the ignition switch.
B. Secure console arm support (item 35) to coupler
nut (item 38) with cap screw (item 37).
1.
C. Place flat washer (item 20), seat belt latch (item
39) and spacer (item 36) between seat and console
arm support (item 35). Secure with cap screw (item
2.
Disconnect seat electrical connector from machine
33)
and second flat washer (item 20).
wire harness (Fig. 8).
D. Fully tighten all fasteners to secure console arm
assembly to seat.
3.
shifting.
Support console arm assembly to prevent it from
4.
harness (Fig. 8).
Connect seat electrical connector to machine wire
4.
(item 32) that secure support bracket (item 30) to sup-
port channel (item 31).
Remove flange nut (item 29) and carriage screw
5.
arm support (item 35) to coupling nut (item 38).
Remove cap screw (item 37) that secures console
1
2
6.
spacer (item 36) and seat belt latch (item 39) from seat
and console arm support (item 35).
Remove cap screw (item 33), flat washers (item 20),
IMPORTANT: Make sure to not damage the electri-
cal harness, control cable or other parts while mov-
ing the console arm assembly.
3
7.
Carefully move console arm assembly away from
seat.
8.
Remove four (4) torx head screws that secure seat
Figure 8
to seat suspension (Fig. 9). Note that the screw near the
seatadjustment handle is longerthan theother three(3)
screws.
1.
2.
Operator seat
3.
Suspension connector
Seat switch connector
9.
Lift seat from seat suspension and remove from ma-
chine.
NOTE: Refer to Operator Seat Suspension in this sec-
tion if seat suspension service is necessary.
1
Installation (Fig. 7)
1.
Carefully position seat to seat suspension.
2.
Secure seat to seat suspension with four (4) torx
head screws (Fig. 9). Make sure that longer screw is
positioned near the seat adjustment handle. Torque
screws 18 ft--lb (25 N--m).
3
4
2
IMPORTANT: Make sure to not damage the electri-
cal harness, control cable or other parts while mov-
ing the console arm assembly.
3.
Position and secure console arm assembly to seat.
Install all fasteners before fully tightening them.
18
(25
ft--lb
N--m)
A. Secure support bracket (item 30) and support
channel (item 31) with flange nut (item 29) and car-
riage screw (item 32).
Figure 9
1.
2.
Seat
3.
Screw (M8x12) (3 used)
Screw (M8x16)
Suspension assembly
4.
Groundsmaster 4100--D/4110--D
Page 7 -- 9
Chassis
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Groundsmaster 10177SL, Toro Groundsmaster 30447, Toro Groundsmaster 30449, Toro Groundsmaster 4100, Toro Groundsmaster 4110 D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)