Removal (Fig. 49)
Park the machine on a level surface, engage the
Installation (Fig. 49)
1.
1. Thread lift hub onto lift cylinder and tighten fully.
parking brake, lower the cutting units, and stop the en-
gine. Remove the key from the ignition switch.
2.
Position lift cylinder inside the cylinder support
bracket and valve mount bracket. Make sure the ports
of the lift cylinder face the hydraulic fitting side of the cyl-
inder support bracket.
CAUTION
3.
Align lift cylinder mounting hole with holes at bottom
of the valve mount bracket. Slide clevis pin through
holes and secure clevis pin with cotter pin.
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil.
4.
Align lift hub holes with the slots on the cylinder sup-
port bracket. Apply grease to flange bushings and install
bushings into the cylinder support bracket slots.
2.
tion Unit Operator’s Manual).
Remove cutting units from front lift arms (see Trac-
5.
hub holes. Slide cylinder guide pin through the cylinder
support bracket, flange bushings, and lift hub.
Make sure flange bushings are aligned with the lift
3.
cylinder (see Traction Unit Operator’s Manual). Label all
connections for reassembly.
Raise and remove hood to get access to the front lift
6.
guide pin by installing flanged head screw fully.
Align hole in cylinder guide pin to lift hub hole. Secure
4.
Disconnect hydraulic hoses (1, 2, 3, and 4) from hy-
draulic fittings (5). Allow hoses to drain into a suitable
container.
7. Secure lift chain clevis (15) to the cylinder guide pin
with clevis pin and cotter pin.
5.
to prevent contamination.
Put caps or plugs on disconnected hoses and fittings
8. Remove caps and plugs from disconnected hoses
and fittings.
6.
the lift cylinder (8).
Remove hydraulic fittings (5) and O–rings (7) from
9. Install O–rings and hydraulic fittings into the lift cylin-
der.
7.
clevis pin from the lift cylinder and frame.
Remove cotter pin (9) from the clevis pin (10). Pull
10.Connect hydraulic hoses to hydraulic fittings on lift
cylinder. Tighten hose connections.
8.
Remove flange head screw (11) from cylinder guide
pin (16) and lift hub (12). Remove cotter pin (13) and cle-
vis pin (14) from the lift chain clevis (15) that is on the hy-
draulic fitting side of the cylinder support bracket (17).
11.Install hood.
12.Install
cutting units to front lift arms (see Traction Unit
Operator’s Manual).
9.
from the lift hub (12).
Support lift cylinder and slide cylinder guide pin (16)
13.Follow
Hydraulic System Start–up procedures.
10.Reach
up from the bottom and rotate lift cylinder so
the bottom port comes out of the slot in the frame. Drop
lift cylinder down and out from the frame.
11.
Remove flange bushings (18) from the cylinder sup-
port bracket (17).
12.Remove
lift hub from the lift cylinder shaft.
Reelmaster 2000–D
Page 4 – 69
Hydraulic System
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Reelmaster 2000-D |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5) Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews.
Really needed this manual. Amazing that Toro would make it so easily available. Full of details.