Toro 02103SL Rev A Reelmaster 2000 D Service Manual

Front and Rear Rollers
NOTE:  This section can be used for both the front and
rear rollers.
Roller Removal
1.
Remove both height–of–cut pins and hairpin cotters
from each roller bracket.
2
2.
Remove both locknuts from the cap screws securing
each angle bracket to the cutting unit.
1
3.
the cutting unit.
Remove cap screws from  both angle brackets and
5
4.
and angle brackets from the cutting unit.
Separate  roller assembly,  height–of–cut brackets,
6
7
4
5.
sembly.
Remove height–of–cut brackets  from the roller as-
10
3
8
4
9
Roller Installation
1.
replace if necessary.
Inspect bushings in height–of–cut bracket for wear;
Figure 12
1.
2.
3.
4.
5.
Height–of–cut pin
Hairpin cotter
Height–of–cut bracket
Lock nut
6.
Angle bracket
7.
8.
9.
Front roller assembly
Flanged bushing
Bushing
NOTE:  The flanged end  of the flanged  bushing must
face  inside toward  the roller  when  the height–of–cut
bracket is installed onto the cutting unit.
Cap screw
10. Carriage bolt
NOTE:  A  soft  hammer  may  be  needed  to  tap  the
height–of–cut bracket  into position on the  hex adjust-
ment nut of the roller.
5.  Mount  roller,   height–of–cut  brackets,  and   angle
brackets to the cutting unit. Secure height–of–cut brack-
ets  and  angle brackets  to  the  cutting  unit  with  cap
screws.
2.
Insert smaller diameter roller  shaft into the height–
of–cut bracket with flanged bushing and bushing. Insert
the other end of the roller shaft into the other height–of–
cut bracket with  bushing. Make sure  that hex of  the
height–of–cut brackets  mate with  the hex  adjust-
ment nut on the roller.
6.  Install both height–of–cut pins and hairpin cotters.
7.
Install locknuts to the cap  screws and secure each
angle bracket to the cutting unit.
8.
Adjust roller level (see Cutting Unit Operator’s Manu-
al).
3.
Hold one height–of–cut bracket  stationary and use
the other bracket as a wrench to loosen or tighten bear-
ing clearance. The roller must not exceed 5 in–lb (0.57
N–m) rolling torque and have no bearing end play.
4.
Make sure height–of–cut brackets are aligned prior
to installing them onto the cutting unit. If necessary after
bearing adjustment, align height–of–cut brackets as fol-
lows:
A.  Remove height–of–cut bracket on  the side with
the flanged bushing.
B.  Adjust height–of–cut bracket  so it  is aligned  to
within + one hex flat of the roller adjustment nut.
C. Align both height–of–cut brackets.
Reelmaster 2000–D
Page 7 – 13
Cutting Units
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 208 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 02103SL Rev A Reelmaster 2000 D Service Manual SKU UPC Model
Krista Renzo on Nov 19, 2016.

Really needed this manual. Amazing that Toro would make it so easily available. Full of details.


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website