Flush Hydraulic System
IMPORTANT: Flush the hydraulic system any time
there is a severe component failure or the system is
contaminated (oil appears milky or black or con-
tains metal particles).
1
IMPORTANT: Flush hydraulic system when chang-
Ing from petroleum base hydraulic fluid, such as
Mobil DTE 15M, to biodegradable fluid, such as Mo-
bil EAL 224H. Operate machine under normal oper-
ating conditions for at least four (4) hours before
draining.
2
1.
Park machine on a level surface. Lower cutting units,
stop engine, engage parking brake, and remove key
from ignition switch.
Figure 32
2.
Clean area around filter mounting area. Remove fil-
1.
2.
Hydraulic reservoir cap
Sight gauge
ter and drain reservoir into a suitable container. Drain
hydraulic system. Drain all hoses, tubes, and compo-
nents while the system is warm. Discard filter.
3.
Inspect and clean reservoir (see Inspecting Reser-
voir Parts).
4.
Make sure filter mounting surface is clean. Apply hy-
draulic oil to gasket on the new filter. Screw filter on until
gasket contacts mounting plate, then tighten filter half a
turn.
2
1
NOTE: Use biodegradable fluid, such as Mobil EAL
224H,
for this step if you are changing to this type of fluid.
Use only hydraulic fluids specified in Traction Unit Oper-
ator’s Manual. Other fluids could cause system dam-
age.
Figure 33
5.
6.
Fill hydraulic reservoir.
1.
Hydraulic filter
2. Footrest
Disconnect electrical connector to the fuel stop sole-
12.Shut
off engine and check for hydraulic oil leaks.
Check oil level in hydraulic reservoir and add correct oil
if necessary.
noid to prevent engine from starting.
7.
Turn ignition key switch to start; engage starter for
ten (10) seconds to prime hydraulic pump. Repeat this
step again.
13.Operate
operating conditions.
the machine for two (2) hours under normal
8.
Attach electrical connector to the fuel stop solenoid.
14.Check
condition of hydraulic oil. If the fluid shows any
signs of contamination, or if you are changing to biode-
gradable fluid, repeat steps 1 through 14 again.
9.
of two (2) minutes.
Start engine and let it idle at low speed for a minimum
15.Resume
maintenance intervals.
normal operation and follow recommended
10.Increase
one (1) minute under no load.
engine speed to high idle for minimum of
11.
Raise and lower cutting units several times.
Reelmaster 2000–D
Page 4 – 41
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Reelmaster 2000-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews. Really needed this manual. Amazing that Toro would make it so easily available. Full of details.