Cutting Reel Motor
Removal (Fig. 43)
1.
Park the machine on a level surface, engage the
parking brake, lower the cutting units, and stop the en-
gine. Remove the key from the ignition switch.
CAUTION
35
ft–lb
N–m)
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil.
(47
4
2
2.
Remove reel motor from cutting unit (see Repair sec-
1
tion of Chapter 7 – Cutting Units).
3
3.
Unscrew flange nut and remove coupling from reel
motor using a puller. Locate and retrieve key.
4.
Clean motor, fittings, and hose connections.
Figure 43
1.
2.
Flange nut
Coupling
3.
4.
Reel motor
Key
NOTE: The position of the fittings on the reel motor is
critical to reconnecting hydraulic hoses.
7.
Place O–ring on face seal of hydraulic fitting. Secure
5.
Matchmark reel motor and all hydraulic fittings for reas-
sembly purposes.
Label all hose connections for reassembly purposes.
hydraulic fitting to the reel motor ensuring that the
matchmarks are aligned. Repeat this step for the re-
maining hydraulic fittings.
6.
Remove hose connections from hydraulic fittings. Al-
8.
nections. Replace any damaged or worn connections.
Inspect threads and sealing surfaces of hose con-
low hydraulic oil to drain from hose into a suitable con-
tainer. Put caps or plugs on disconnected hoses to
prevent contamination.
9. Secure hose connection to the hydraulic fitting. Re-
peat this step for the remaining hydraulic fittings.
7.
Remove hydraulic fittings and O–rings from reel mo-
tor. Discard O–rings.
10.Install reel motor to cutting unit (see Repair section
of Chapter 7 – Cutting Units).
Installation (Fig. 43)
11.
Follow Hydraulic System Start–up procedures.
1.
2.
3.
Position key and place coupling on reel motor shaft.
Install flange nut and torque nut 35 ft–lb (47 N–m).
Make sure hydraulic fitting ports and O–ring sealing
surfaces on the reel motor are clean.
4.
Remove caps or plugs that were put on any hydraulic
lines or fittings during disassembly.
5.
6.
Apply clean hydraulic oil to all O–rings.
Inspect threads and sealing surfaces of hydraulic fit-
tings. Replace any damaged or worn fittings.
Reelmaster 2000–D
Page 4 – 55
Hydraulic System
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Reelmaster 2000-D |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews. Really needed this manual. Amazing that Toro would make it so easily available. Full of details.