Wheel Motor
Front Wheel Motor Removal (Fig. 40)
1.
Park the machine on a level surface, engage the
parking brake, lower the cutting units, and stop the en-
gine. Remove the key from the ignition switch.
9
(LH)
4
7
(LH)
CAUTION
3
6
(LH)
Operate all hydraulic controls to relieve system
pressure and avoid injury from pressurized hy-
draulic oil.
5
8
16
5
1
10
16
14
2
2.
Remove wheel and brake assembly from unit (see
Repair section of Chapter 6 – Chassis).
12
3.
Clean wheel motor and hydraulic connections. Label
RIGHT
all tube hose connections for reassembly purposes. Put
caps or plugs on any hydraulic lines or fittings left open
or exposed.
15
FRONT
13
4.
Disconnect tube connections from hydraulic fittings
11
on motor to be removed. On the left–hand wheel motor,
also disconnect hydraulic hose (4) from hydraulic fitting
on motor. Allow hydraulic oil to drain from tubes and
hose into a suitable container.
Figure 40
1.
2.
3.
4.
5.
6.
7.
8.
Wheel motor (LH shown)
Tube connection
Tube connection
Hyd. hose (LH motor)
Hydraulic fitting
9. O–ring (LH motor)
10. Socket head screw
11. Lock nut
12. Support frame
13. Brake bracket
14. Grass shield
15. Spacer
5.
Support wheel motor. Remove four socket head
O–ring (LH motor)
Hyd. fitting (LH motor)
O–ring
screws and lock nuts from support frame. Remove
brake bracket (13), grass shield (14), and spacers (15).
Pull wheel motor from the support frame.
16. O–ring
5.
motor. On the left–hand motor, also install hose connec-
tion (4) to hydraulic fitting (7). Tighten connections.
Install tube connections to hydraulic fittings on wheel
6.
wheel motor.
Remove hydraulic fittings and O–rings from the
Front Wheel Motor Installation (Fig. 40)
6.
Install wheel and brake to machine (see Repair sec-
tion of Chapter 6 – Chassis).
1.
Place and support wheel motor into the support
frame. Insert four socket head screws through the sup-
port frame and wheel motor.
7.
Follow Hydraulic System Start–up procedures.
2.
Slide spacers, grass shield, and brake bracket onto
the cap screws and wheel motor. Tighten lock nuts onto
cap screws.
3.
Remove caps or plugs that were put on any hydraulic
lines or fittings during disassembly.
4.
Install hydraulic fittings (5 and 6) onto the wheel mo-
tor. On the left–hand wheel motor, also install hydraulic
fitting (7) onto the wheel motor. Tighten hydraulic fit-
tings.
Hydraulic System
Page 4 – 52
Reelmaster 2000–D
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Reelmaster 2000-D |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5) Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews.
Really needed this manual. Amazing that Toro would make it so easily available. Full of details.