Full or Wiehle Roller Assembly
Sectional Roller Assembly
1.
ings and seals.
Make sure all parts are clean prior to installing bear-
1. Make sure all parts are clean prior to installing bear-
ings and seals.
2.
seal into each end of the roller. Make sure that cupped
side of the seal faces the inside of the roller.
On a full roller, grease inner seal lips and install inner
2. Press two bearing cups into each sectional roller.
Make sure narrow end of taper faces the inside of the
roller.
3.
cup faces the inside of the roller. Press a cup into each
end of the roller.
Make sure narrow end of the taper on the bearing
3. Secure sectional roller shaft in a vise. Make sure
shaft is level.
4.
Pack all bearing cones with No. 2 general purpose
4.
Secure roller in a vise in a level position.
lithium base grease.
5.
Pack both bearing cones with No. 2 general purpose
NOTE: Install the bearing cone with the seal into the
lithium base grease.
end of the roller that faces the inner part of the shaft.
6.
end of the roller.
Install a bearing cone into the bearing cup at each
5. On both rollers, install a bearing cone into the bear-
ing cup at each end of the roller.
7.
of seal facing out. Grease seal lips and press a seal into
each end of the roller.
Position outer seal to the roller with the hard surface
6. Grease outer seal lips and install seal into the end of
each roller. Make sure the hard surface of seal faces out.
7.
Slide each roller onto the shaft.
8.
one end) through the bearing cones, seals, and roller.
Slide roller shaft (with adjustment nut installed on
8.
Tighten each nut to seat both bearings of each roller.
Roller should be rotated to seat both bearings.
Install adjustment nut onto each end of the shaft.
9.
Install remaining adjustment nut onto shaft and tight-
en it to seat both bearings. Roller should be rotated to
seat bearings.
9.
Back off both adjustment nuts to allow the rollers to
spin freely. Tighten both adjustment nuts again so there
is no bearing end play and rolling torque does not ex-
ceed 5 in–lb (0.57 N–m).
10.Back
off both adjustment nuts to allow the roller to
spin freely. Tighten both adjustment nuts again so there
is no bearing end play and rolling torque does not ex-
ceed 5 in–lb (0.57 N–m).
10.Grease
al).
bearings (see Cutting Unit Operator’s Manu-
11.
al).
Grease bearings (see Cutting Unit Operator’s Manu-
Reelmaster 2000–D
Page 7 – 15
Cutting Units
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Reelmaster 2000-D |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5) Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews.
Really needed this manual. Amazing that Toro would make it so easily available. Full of details.