Toro 02103SL Rev A Reelmaster 2000 D Service Manual

Hydraulic System Start–up
NOTE:  When initially starting the hydraulic system with
new or rebuilt components such as  motors, pumps, or
lift cylinders, it is important that this start–up procedure
be used. This procedure reduces the chance of damag-
ing the system or its components from not purging  the
system of air.
CAUTION
Be careful when operating the cutting unit reels.
Contact with the reel or other moving parts can
result in personal injury.
1.
After the hydraulic  system components have been
properly installed and if the traction pump was rebuilt or
replaced, make sure traction  pump housing is at least
half full of clean hydraulic oil.
9.  After the hydraulic system starts to show signs of fill,
accomplish the following:
2.
cured tightly.
Make sure all hydraulic connections and lines are se-
A.  If a reel motor was replaced or rebuilt, run the cut-
ting units  at the minimum speed  setting (under no
load) for 10 minutes in both directions.
3.
Make sure hydraulic reservoir is full. Add correct oil
if  necessary  (see Traction  Unit  Operator’s  Manual).
Drain, flush,  and refill  hydraulic system reservoir  and
change oil filter if component failure was severe or sys-
tem is contaminated.
B.  If a reel motor drive pump was replaced or rebuilt,
run the cutting  units at the minimum  speed setting
(under no load) for 10 minutes.
C. If a traction pump or a wheel motor was replaced
or rebuilt, run the traction unit so the wheels  slowly
turn for 10 minutes.
4.
Disconnect electrical connector to the fuel stop sole-
noid to prevent engine from starting.
5.
ment, binding, or broken parts.
After repairs, check control linkage for proper adjust-
10.Operate the traction unit and cutting unit by gradually
increasing their work load to full over a 10 minute period.
6.
unit switch is off.  Turn ignition key switch to  start; en-
gage starter for fifteen (15) seconds to prime pump.
Make sure traction pedal is in neutral and the cutting
11.Stop the machine. Check hydraulic reservoir and fill
if necessary. Check hydraulic components for leaks and
tighten any loose connections.
7.
8.
Attach electrical connector to the fuel stop solenoid.
Make sure traction pedal is in neutral and the cutting
unit switch is off. Start engine and run it at low idle. The
charge pump should pick up oil and fill the hydraulic sys-
tem. If there is no indication of fill in 30 seconds, stop the
engine and determine the cause.
Hydraulic System
Page 4 – 42
Reelmaster 2000–D
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 208 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 5 out of 5)
Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 02103SL Rev A Reelmaster 2000 D Service Manual SKU UPC Model
Krista Renzo on Nov 19, 2016.

Really needed this manual. Amazing that Toro would make it so easily available. Full of details.


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website