6.
Repairs section of Chapter 4 – Hydraulic System).
Install hydraulic pump assembly (see Service and
16.Fill hydraulic reservoir with hydraulic fluid (see Trac-
tion Unit Operator’s Manual). Check reservoir for leaks.
7.
After engine and pump installation, verify pulley
17.Slide the left foot rest onto the brake rod. Reinstall
cap screws and flange nut securing the left footrest to
the frame. Tighten cap screws (Fig. 10).
alignment across engine and pump pulley faces with a
straight edge. The gap between both faces must not ex-
ceed 0.030” (0.8 mm).
18.Connect
brake rod to brake arm. Install and lock cot-
8.
Adjust traction pump belt (see Traction Unit Opera-
ter pin to the brake rod (Fig. 11).
tor’s Manual).
19.Reinstall
fender bracket and left fender to the radia-
9.
Reconnect throttle cable to injector pump.
tor side of the frame (Fig. 10).
A. Route throttle cable to injector pump on engine.
A. Secure both cap screws and left fender bracket to
the frame.
B. Reinstall the throttle cable into the swivel clamp
on the pump speed control lever.
B. Reinstall remaining cap screws and flange nuts
securing the fender to the fender bracket and frame.
C. Place cable under cable clamp.
C. Secure cap screw and flange nut to the left foot
rest and the left fender.
D. Adjust throttle control (see Adjust Throttle Con-
trol).
20.Adjust
Manual).
hand brake (see Traction Unit Operator’s
10.Remove
bly. Connect hoses to the engine.
plugs installed in hoses during disassem-
21.Check
Manual).
engine oil level (see Traction Unit Operator’s
A. Connect return to tank fuel hose to the injector
pump fitting (Fig. 12). Tighten hose clamp.
22.Connect
cables at the battery.
negative (–) and then positive (+) battery
B. Connect fuel hose from the fuel filter/water sepa-
rator (Fig. 12). Tighten hose clamp.
23.Bleed
Manual).
fuel system (see Traction Unit Operator’s
C. Connect upper and lower radiator hoses to the
engine. Tighten hose clamps.
24.Replace
access covers to the engine.
11.
Reinstall exhaust system (see Exhaust System
Installation).
12.Reinstall
13.Reinstall
A. Reinstall left rear panel (radiator side) which sup-
ports the instrument panel.
air cleaner (see Air Cleaner Installation).
radiator (see Radiator Installation).
B. Reinstall right side panel which accesses the
traction pump drive belt.
14.Add
Manual).
coolant to radiator (see Traction Unit Operator’s
C. Reinstall hood to the machine.
15.Open
fuel shut–off valve under the fuel tank.
Engine
Reelmaster 2000–D
Page 3 – 18
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Reelmaster 2000-D |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 5 out of 5) Lawn and Garden readers have rated Toro 02103SL Rev A Reelmaster 2000 D Service Manual 5.0 out of 5.0 based on 1 product reviews.
Really needed this manual. Amazing that Toro would make it so easily available. Full of details.