Service Air Cleaner
Note:
Perform this maintenance procedure at the in-
Compressed Air Method
terval specified in the Operator’s Manual or Chapter 2
–
Product Records and Maintenance.
CAUTION
1.
Park machine on a level surface, stop engine, en-
gage parking brake, and remove key from the ignition
switch.
Use eye protection such as goggles when using
compressed air.
2.
Raise bed and support with prop rod (see Operator’s
Manual).
IMPORTANT: Maximum air pressure must not ex-
ceed 100 psi to prevent damage to the element.
3.
Check air cleaner body and hoses for damage which
could possibly cause an air leak. Replace air cleaner
body if damaged.
A. Blow compressed air from the inside to the out-
side of the dry filter element.
4.
air cleaner body. Separate cover from the body. Clean
inside of air cleaner cover.
Release latches securing the air cleaner cover to the
B. Keep air hose nozzle at least 2 inches (5 cm) from
the filter. Move nozzle up and down while rotating the
filter element. Inspect for holes and tears by looking
through the filter toward a bright light.
5.
Gently slide filter out of the air cleaner body to reduce
the amount of dust dislodged. Avoid knocking filter
against the air cleaner body.
8.
for shipping damage. Check sealing end of the filter. Do
not install a damaged filter.
If filter element is being replaced, inspect new filter
IMPORTANT: Do not wash or reuse a damaged filter.
9.
Insert new (or cleaned) filter correctly into the air
6.
7.
Inspect filter. Discard filter if damaged.
cleaner body. Make sure filter is sealed properly by ap-
plying pressure to the outer rim of the filter when instal-
ling. Do not press on the flexible center of the filter.
Clean filter element using either the washing method
or compressed air method:
10.Reinstall
cover and secure latches.
Washing Method
A. Prepare a solution of filter cleaner and water.
Soak filter element for about 15 minutes. Refer to
directions on the filter cleaner carton for complete in-
formation.
IMPORTANT: Maximum water pressure must not
exceed 40 psi to prevent damage to the filter ele-
ment.
3
B. After soaking the filter for 15 minutes, rinse it with
clear water. Rinse filter from the clean side to the dirty
side.
IMPORTANT: Do not use a light bulb to dry the filter
element because damage could result.
2
1
C. Dry filter element using warm, flowing air that
does not to exceed 160oF (71oC), or allow element to
air–dry.
Figure 9
3.
1.
2.
Air cleaner latches
Cover
Filter element
Briggs & Stratton Gasoline Engine
Page 3 – 8
Workman 2100/2110
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Workman 1100, Toro Workman 1110, Toro Workman 2100, Toro Workman 2110 |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)