Adjustments
Adjust Ground Speed (Vehicles With Transaxle Governor)
Note:
All Workman 1100 and 1110 models are
equipped with a transaxle governor. Workman 2100 and
models with serial numbers below 240000000 are
C. If unable to identify the driven clutch RPM, an al-
ternate method to verify ground speed would be to
determine the distance that the vehicle will travel in
three (3) seconds with the accelerator pedal to the
floor. Use the following chart to determine if vehicle
ground speed is correct:
2110
also equipped with a transaxle governor.
WARNING
DISTANCE IN
3 SECONDS
GROUND
SPEED
MODEL
1100
Vehicles operating at ground speeds greater than
the recommended speed will require further
distances to fully stop. Do not adjust ground
speed greater than specified.
62 ft (18.9 m)
70 ft (21.3 m)
14 mph (23 kph)
16 mph (26 kph)
2100/2110
6.
odized rivet and retain anti–tamper bracket for rein-
stallation (Fig. 4).
If ground speed adjustment is necessary, drill out an-
1.
move key from the ignition switch. Raise and latch cargo
bed.
Park machine on a level surface, stop engine, and re-
7.
Adjust throttle cable (accelerator pedal to transaxle)
at the cable bracket until the correct driven clutch RPM
is obtained with the accelerator pedal fully to the floor
(Fig. 4).
WARNING
Before jacking up the machine, review and follow
Jacking Instructions in Chapter 1 – Safety.
8.
with a new anodized rivet (Toro P/N 99–7122) (Fig. 4).
Reinstall anti–tamper bracket to the cable bracket
2.
Jack up rear of vehicle so both rear wheels are at
9. Lower machine to ground. Lower cargo bed.
least 1 inch (25mm) off the ground with the rear axle
tubes supported on jack stands.
4
3.
vehicle from moving.
Chock front and rear of both front tires to prevent the
1
4.
Lock transaxle into neutral (see Transaxle Neutral
Position in Chapter 1 – Safety).
3
5.
Verify ground speed as follows:
A. Start engine and hold accelerator pedal to the
floor.
2
B. Verify driven clutch RPM with a tachometer. With
the accelerator pedal to the floor, the driven clutch
speed should be as follows:
Figure 4
1.
2.
Anodized rivet
Anti–tamper bracket
3.
4.
Throttle cable
Cable bracket
MODEL
1100
DRIVEN CLUTCH RPM
2900 – 3000 RPM
3250 – 3350 RPM
2950 – 3050 RPM
2100
2110
Drive Train
Page 5 – 4 Rev. A
Workman 1100/1110/2100/2110
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Workman 1100, Toro Workman 1110, Toro Workman 2100, Toro Workman 2110 |
| Download File |
|
| Document Type | Catalog |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)