Stub Axle and Driveshaft
Loctite #242
220 to 250 ft–lb
75 ft–lb
(101 N–m)
Loctite #242
(298
to 339 N–m)
27
28
25
13
29
23
22
11
10
12
Loctite #680
21
9
8
40
(54
to 60 ft–lb
to 81 N–m)
7
6
5
26
4
45 to 65 ft–lb
24
(61
to 88 N–m)
20
19
1
18
30
200
(271
to 250 ft–lb
to 339 N–m)
17
Anti–seize
Lubricant
16
15
RIGHT
14
FRONT
3
2
Figure 21
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Lug nut (5 used per wheel)
Flange head screw
Wheel assembly
Brake drum
11. Brake cable clip
12. Axle housing
21. End yoke
22. Flat washer
23. Flange lock nut
24. Yoke strap (2 used per yoke)
25. Bolt (4 used per yoke)
26. Driveshaft assembly
27. Lock nut (2 used per driveshaft)
28. Cap screw (2 used per driveshaft)
29. Hardened washer (2 per driveshaft)
30. Parking brake cable
13. Flange head screw (3 used per wheel)
14. Outer bearing cone
15. Outer bearing cup
16. Spacer
Stub axle
Lock washer (5 used per wheel)
Drive stud (5 used per wheel)
Cap screw (4 used per wheel)
Lock washer (4 used per wheel)
Brake assembly
17. Bearing spacer
18. Inner bearing cup
19. Inner bearing cone
20. Bearing seal
Removal (Fig. 21)
Park machine on a level surface, stop engine, and re-
5. Loosen flange lock nut that secures end yoke to stub
axle. Remove flange lock nut, flat washer, and flange
head screw. Pull end yoke from stub axle.
1.
move key from the ignition switch.
6.
Carefully slide stub axle from axle housing.
2.
Chock front wheels. Raise rear wheel using a jack or
hoist (see Jacking Instructions in Operator’s Manual).
Block rear of machine.
7. To remove driveshaft from transaxle, loosen and re-
move lock nuts, cap screws, and hardened washers se-
curing driveshaft to splined axle shaft of transaxle. Slide
driveshaft outward and remove from transaxle.
3.
Loosen and remove lug nuts. Remove rear wheel.
Remove brake drum (see Rear Wheels and Brakes in
Service and Repairs Section of Chapter 8 – Chassis).
8. To remove axle housing from machine:
NOTE: Loosening driveshaft at transaxle will allow eas-
ier driveshaft removal from end yoke.
A. Remove brake assembly from axle housing (see
Rear Wheels and Brakes in Service and Repairs
Section of Chapter 8 – Chassis).
4.
Remove the straps securing driveshaft bearing
cross to the end yoke, then disconnect driveshaft from
the end yoke.
B. Remove three (3) flange head screws that secure
axle housing to machine frame. Remove axle hous-
ing.
Drive Train
Page 7 – 22
Multi Pro 1200/1250
| Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
|---|---|
| Tags | Toro Multi Pro 1200, Toro Multi Pro 1250 |
| Download File |
|
| Document Type | Service Manual |
| Language | English |
| Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
| Document File Type | |
| Publisher | toro.com |
| Wikipedia's Page | Toro Company |
| Copyright | Attribution Non-commercial |
(0 votes, average: 0 out of 5)