Toro 03113SL Rev E Greensmaster 3150 Service Manual

Optional Backlap Kit Flow Control and TwoPosition
Directional Valves (Fig. 58)
6.   Reinstall the cartridge valve (7 or 13):
A.  Lubricate new O--ring and backup ring of seal kit
(8
or 11) with clean hydraulic oil and install. The O--
CAUTION
ring and backup ring  of seal kit must be arranged
properly on the cartridge valve (7 or 13) for proper
operation and sealing.
Before continuing further, read and  become fa-
miliar with  General  Precautions for  Removing
and Installing Hydraulic System Components.
B.  Thread valve carefully  into the applicable port
(RD1 or FC1). The valve should go in easily without
binding. Torque valve to 35 ft--lb (47 Nm).
1.
Remove knob assembly:
7.
Reinstall knob assembly:
A.  Unscrew and remove knob (17). Remove both
jam nuts (18).
A.  Install applicable locating plate (25 or 26) so that
the pin seats into the locating hole.
B.  Slideoffapplicableindicatorplate(6or19)being
careful  not to  lose  springs  (20 or  21).  Remove
springs.
B.  Turn the threaded cartridge valve (7 or 13) stem
carefully clockwise until it stops.
C. Face   detent   plate  (22)   counterbore  down.
Threaddetentplatedownontothevalvestem     untilit
is stopped by the locating plate.  Turn detent plate
back counterclockwise 1/4 turn.
C. Loosensetscrew(23)andslidedetentplate(22)
off the applicable cartridge valve (7 or 13) stem.
D. Remove  the applicable  locating plate with  pin
(25
ifold (27).
or 26) from the cartridge valve stem and man-
D. Center  one  detent plate  hole over  a  locating
plate indentation. Drop  a ball (24) into each  hole,
then drop a spring (20 or 21) into each hole.
2.
(8
Remove cartridge valve (7 or 13) and seal kit
or 11).
E.  Onflowcontrolvalve(7),placeindicatorplate(6)
overthedetentplate.Makesurethearrow     points di-
rectly at the number 1 on the locating plate.
3.
Visually inspect  the port  in  the manifold  (27) for
damage to the sealing surfaces, damaged threads, and
contamination.
F.  On  directional  cartridge  cartridge  valve (13),
place  indicator plate  (19)  over the  detent  plate.
Make sure the arrow points to the right at 45o.
4.
aged sealing surfaces and contamination.
Visually inspect cartridge valve  (7 or 13) for dam-
G. While pushing down on the indicator plate (6 or
A.  Contamination may  cause  valves  to  stick  or
hang up, it can become  lodged in small valve ori-
fices or seal areas causing malfunction.
19)
and compressing  the springs, thread  down a
jam nut (18).  While tightening the set  screw (23),
tighten jam nut at the same time using a 7/16 -- inch
wrench
B.  If sealing surfaces  appear pitted or  damaged,
the hydraulic system may be overheating or  there
may be water in the system.
H. Thread  second jam  nut all  the way  down the
valve stem. Apply “Loctite 242” or equivalent on the
valve stem  threads. Screw knob  (17) all the  way
down until it hits the upper jam nut.
CAUTION
I.   On directional cartridge valve (7), turn knob (17)
counterclockwise so the arrow is 90o with the back
of the manifold (27). Simultaneously tighten upper
jam nut (18) and turn knob so itis tightand thearrow
is pointing 45o to the right in line with the indicator
Use eye protection such as goggles when using
compressed air.
5.
If necessary, clean cartridge valve  (7 or 13) using
plate (6).
clean mineral spirits. Submerge valve in clean mineral
spirits toflush outcontamination. Particles asfineastal-
cum powder can affect the operation  of high pressure
hydraulic valves. Use compressed air for cleaning.
J.  On flow  control cartridge valve (13), turn  knob
(17)
counterclockwise until the arrow points at the
number “5”. Simultaneously tighten upper  jam nut
andturnknobsoitistightandthearrowispoint-
(18)
ing at the number “1” on the locating plate (19).
Greensmaster 3150
Page 4 -- 87
Hydraulic System (Rev. E)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 306 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 03113SL Rev E Greensmaster 3150 Service Manual SKU UPC Model
kurt on May 29, 2014.

Safety switches not working


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website