7.
Remove lock nut (item 35), tab washer (item 34) and
plow bolt (item 27) that secure drive side groomer arm
assembly to drive side plate. Do not change height--of--
cut screw adjustment. Remove drive side groomer arm
assembly from cutting unit.
3
4
8.
Remove front roller assembly from cutting unit.
To prevent groomer shaft from turning when re-
Note:
moving driven pulley, use wrench on shaft flats to hold
shaft.
9.
Remove the flange nut (item 17) that secures driven
1
pulley (item 32) to groomer shaft. Remove driven pulley
fromshaft. Locate and retrieve square key (item 31)that
locates pulley on shaft.
2
Figure 7
Note:
moving drive pulley, block reel with piece of wood.
To prevent cutting reel from turning when re-
1.
2.
Cap screw
Front roller shaft
3.
4.
Groomer shaft assembly
Locknut/spring washer
10.Remove
flange head screw (item 4) and washer
(item 5) that secure drive pulley (item 7) to the cutting
reel shaft. Slide drive pulley from cutting reel.
11.
groomer drive side plate (item 10) to the cutting unit
frame. Remove the groomer drive side plate assembly.
Remove two shoulder nuts (item 8) that secure the
2
12.Remove
plate (Fig. 8).
the cap plug (item 21) from non--drive side
1
13.Remove
the flange nut that secures the groomer
shaft to the non--drive side plate.
Figure 8
14.Pull
the groomer reel from the non--drive side plate.
seals, bushings and bearings in side plates
1.
2.
Roller retaining cap screw
Cap plug
15.Inspect
for wear or damage. Replace components as needed.
1
2
Installation
1.
Park machine on a clean and level surface, lower
cutting units completely to the ground, stop engine, en-
gage parking brake and remove key from the ignition
switch.
3
2.
LH side plates. Make sure that seals, bushings and
bearings are properly positioned in side plates.
Apply a light coating of grease to seal lips in RH and
3.
Carefully place groomer reel assembly into the non--
Figure 9
drive side plate bearings taking care not to damage seal
in side plate. Thread flange nut (item 17) onto the shaft
threads but do not tighten.
1.
2.
Drive side plate
Drive pulley
3. Driven pulley
4.
Makesurethatgroomer shim(item11)isinstalledon
groomer drive side of cutting unit.
5.
Carefully place drive side plate onto groomer shaft
taking care not to damage seals in side plate. Position
side plate to the cutting unit frame and secure with two
shoulder nuts (item 8).
Greensmaster 3150
Page 10.1 -- 9
Groomer (DPA Cutting Unit) (Rev. A)
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Greensmaster 3150 |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2) Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Safety switches not working