Procedure for Reel Motor Case Drain Flow Test:
Make sure hydraulic oil is at normal operating tem-
perature by operating the machine for approximately 10
minutes. Make sure the hydraulic tank is full.
9. After achieving 1000 PSI (69 bar), place discon-
nected motor case drain hose into a container gra-
duated in ounces or milliliters (Tool TOR4077: see
SpecialTools)andcollecthydraulic fluidfor15seconds
(Fig. 24).After15 seconds,remove hoseend fromcon-
tainer.
1.
2.
Park machine on a level surface with the cutting
units lowered. Make sure engine is off and the parking
brake is engaged.
10.
control lever to NEUTRAL position. Open control valve
Disengage cutting units by positioning functional
on tester and stop the engine.
CAUTION
11.
Record test results.
Measuretheamountofoilcollectedinthecontainer.
Before continuing further, read and become fa-
miliar with Precautions for Hydraulic Testing.
12. If case drain flow was greater than 8 ounces (236
ml) (0.25 GPM/1 LPM) in 15 seconds, repair or replace
the reel motor as necessary.
3.
hose from motor.
Forthesuspected badreelmotor,disconnect return
13.
connect hose to the pump.
Disconnect tester from motor and return hose. Re-
4.
connected return hose. Make sure the flow control
valve on the tester is fully open.
Installtesterinserieswiththereelmotorandthedis-
14.
drain hose to the bulkhead fitting. Test other reel motors
as needed.
Removeplugfrombulkheadfitting.Reconnectcase
5.
on thehydraulic manifoldis inthe mowposition andreel
If a back lap kit is installed, make sure backlap knob
speed is set to maximum.
6.
Disconnect hose from case drain of the motor to be
tested at the bulkhead fitting.
A. Plug the bulkhead port.
B. Leave the case drain hose from the motor open
and place open end of disconnected hose into a
drain pan.
7.
One person should sit on the seat and operate the
machine while another person reads the tester and
measures case drain leakage. Make sure functional
control lever is in NEUTRAL.Start engine and move the
throttle to full speed (2850 + 50 RPM).
Figure 24
CAUTION
Keep away from reels during test to prevent per-
sonal injury from the rotating reel blades.
8.
Engage reels by positioning the functional control
lever to MOW position. While watching pressure gauge,
slowly close flow control valve on the tester until a pres-
sure of 1000 PSI (69 bar) is obtained.
Figure 25
Greensmaster 3150
Page 4 -- 45
Hydraulic System (Rev. E)
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Greensmaster 3150 |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2) Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Safety switches not working