Service and Repairs
Hydraulic Reel Motor
IMPORTANT: When performing maintenance pro-
cedures on the cutting units, store the cutting unit
reelmotorsinsupport tubesontheframetoprevent
damage to the hoses. Do not raise suspension to
transport position when the reel motors are in the
holders in the traction unit frame. Damage to the
motors or hoses could result.
Inspection
1.
if necessary (see Reel Removal and Installation in this
chapter of this manual).
Check reel drive coupler splines for wear. Replace
Installation
1.
purpose lithium base grease.
Coat spline shaft ofthe motor with clean No. 2multi-
Removal
1.
Park machine on a clean and level surface, lower
2.
tor into themotor adapter plateand leaveapproximately
1/2
3.
Install the flange head screws for the reel drive mo-
cutting units completely to the ground, stop engine, en-
gage parking brake, and remove key from the ignition
switch.
inch (12.7 mm) of threads exposed on each screw.
Install motor by rotating the motor clockwise so the
2.
3.
lic motor to the motor adapter plate. Rotate motor clock-
wise, and remove motor.
Remove basket from carrier frame.
motor flanges clear the flange head screws.
Loosen flange head screws that secure the hydrau-
4.
flanges are encircling the flange head screws. Tighten
flange head screws.
Rotate the motor counterclockwise until the motor
4.
Place protective plastic cap (see Special Tools) into
the hole in the motor adapter plate.
Backlapping (Units without Optional Backlap/Variable Reel Speed Kit)
CAUTION
TOP FACE
REMOVE
BURR
RELIEF ANGLE
Be careful when backlapping the reel because
contact with the reel or other moving parts can
result in personal injury.
FRONT
FACE
FRONT ANGLE
1.
Remove reel motors from the cutting units and cut-
ting units from the lift arms and pull frame (see Cutting
Unit Removal and Installation).
Figure 10
For a better cutting edge, run a file across the
front face of the bedknife when the lapping operation is
completed. This will remove any burrs or rough edges
that may have built up on the cutting edge.
2.
by inserting a piece of 3/8--inch socket extension drive
into the splined reel drive coupling.
Connectthebacklapping machinetothecuttingunit
Note:
3.
Attach backlap motor or drive to the socket exten-
sion.
4.
in the Toro General Service Training Book, Reel Mower
Basics (part no. 09168SL).
Follow instructions and procedures for backlapping
Dual Point Adjust Cutting Units
Page 10 - 8 Rev. E
Greensmaster 3150
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Greensmaster 3150 |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2) Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Safety switches not working