Toro 03113SL Rev E Greensmaster 3150 Service Manual

Hydraulic System Start--up
Note:
When initially starting the hydraulic system with
new or rebuilt components such as motors, pumps, or
lift cylinders, it is important that this start--up procedure
be used. This procedure reduces the chance of damag-
ing the system or its components from not purging the
system of air.
CAUTION
Be careful when operating the cutting unit reels.
Contact with the reel or other moving parts can
result in personal injury.
1.
After the hydraulic system components have been
properly installed and if the traction pump was rebuilt or
replaced, make sure traction pump housing is  at least
half full of clean hydraulic oil.
10.
Afterthehydraulicsystemstartstoshowsignsoffill,
accomplish the following:
A.  If a reel motor was replaced  or rebuilt, run the
cutting units at the minimum speed  setting (under
no load) for ten (10) minutes in both directions.
2.
secured tightly.
Make sure all hydraulic connections  and lines are
3.
Make sure hydraulic reservoir is full. Add correct oil
B.  If a reel motor drive pump was  replaced or re-
built,runthecutting  unitsattheminimumspeedset-
ting (under no load) for ten (10) minutes.
ifnecessary (seeCheckHydraulic  SystemFluid).Drain,
flush, and refill hydraulic system reservoir and change
oil filter if  component failure was  severe or system is
contaminated.
C. Ifa  traction pump or a wheel motor was replaced
or rebuilt, run the traction unit so the wheels slowly
turn for ten (10) minutes.
4.
justment, binding, or broken parts.
After repairs, check  control linkage for proper ad-
11.
ly increasing their work load to full over aten (10) minute
period.
Operatethetractionunitandcuttingunitbygradual-
5.
ting unit switch is off.
Make sure traction pedal is in neutral and the cut-
6.
to prevent the engine from starting.
Disconnect both spark plug wires from spark plugs
12.
sary. Check hydraulic components for leaks and tighten
any loose connections.
Stop the machine. Check reservoir and fill if neces-
7.
(10)
Turn ignition key switch and engage starter for ten
seconds to the prime pump. Return ignition switch
tooffandwaitoneminutetoallowstartertocool.Repeat
step a second time.
8.
Reconnect spark plug wires to spark plugs.
9.
Make sure traction pedal is in neutral and the cut-
ting unit switch is off. Start engine and run it at low idle.
The charge pump should pick up oil and fill the hydraulic
system. If there is no indication of fill in thirty (30) sec-
onds, stop the engine and determine the cause.
Greensmaster 3150
Page 4 -- 53
Hydraulic System (Rev. E)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 306 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 03113SL Rev E Greensmaster 3150 Service Manual SKU UPC Model
kurt on May 29, 2014.

Safety switches not working


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website