Toro 03113SL Rev E Greensmaster 3150 Service Manual

Procedure for Mow  Circuit Relief Valve  (R1) Pres-
sure Test:
10. Onmachineswithserialnumberabove270000000,
system  pressure should  be  from 2700  to  3300 PSI
(186.3
to 227.7 bar). Record test results.
1.
Make sure hydraulic oil is at normal operating tem-
perature by operating the machine for approximately 10
minutes.
A.  If this specification is met, go to step 11.
B.  If specification is not met, open control valve on
tester, shut off  engine and remove solenoid  relief
valve(S1R1)onmanifold(Fig.23).Cleanorreplace
valve (see Hydraulic Manifold Service (Serial Num-
ber Above 270000000) in the Service and Repairs
section  of this  chapter). Retest  relief  valve (R1)
pressure.
2.
units lowered. Make sure engine is off and the parking
brake is engaged. Make sure the hydraulic tank is full.
Park machine  on a level  surface with  the cutting
CAUTION
11.
er and shut off engine.
Disengage cutting units.Opencontrol valve ontest-
Before continuing further, read and  become fa-
miliar with Precautions for Hydraulic Testing.
12.
Disconnect tester from manifold and hose. Recon-
nect hose to the bulkhead connection.
3.
Thoroughly clean  and then disconnect hose  con-
nection on the bulkhead that leads to the left reel motor.
13.
Correctly readjust bedknife on all cutting units.
4.
and bulkhead connection. Make sure the flow control
Install tester in series  with the disconnected hose
valve on the tester is fully open.
FRONT
5.
To prevent  reel damage,  temporarily adjust  bed-
knifeonallcuttingunitstoallowclearancebetweenbed-
knife and reel (no contact).
1
6.
On machines with backlap capabilities, make sure
backlap knob on the hydraulic manifold  is in the mow
position.Makesurereelspeedknob(FC1)issettohigh-
est speed setting (fully open).
CAUTION
2
Figure 22
Keep away from reels during test to prevent per-
sonal injury from the rotating reel blades.
1.
2.
Hydraulic manifold (serial number under 260999999)
Relief valve (R1)
7.
50
Start engine and move throttle to full speed (2850 +
RPM. Engage the cutting units.
2
FRONT
8.
ing the flow control valve on the tester to fully closed.
Watch pressure gauge carefully while slowly clos-
9.
On machines with serial number under 260999999,
system pressure should be from 2160 to 2640 PSI (149
to 182.2 bar). Note: If a dethatching kit is installed, sys-
tem pressure should be from 2700 to 3300 PSI (186.3
to 227.7 bar). Record test results.
A.  If this specification is met, go to step 11.
1
B.  If specification is not met, open control valve on
tester, shut off engine and  adjust relief valve (R1)
(Fig. 22) (see Adjust Manifold Relief  Valves in the
Adjustments section of this Chapter). After adjust-
ment, retest relief valve (R1) pressure.
Figure 23
1.
2.
Hydraulic manifold (serial number above 270000000)
Solenoid relief valve (S1R1)
Greensmaster 3150
Page 4 -- 43
Hydraulic System (Rev. E)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 306 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 03113SL Rev E Greensmaster 3150 Service Manual SKU UPC Model
kurt on May 29, 2014.

Safety switches not working


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website