Engine Removal (Fig. 5)
Parkmachineonalevelsurface,lowercuttingunits,
stop engine, engage parking brake, and remove key
from the ignition switch.
Engine Installation (Fig. 5)
1.
1. Support the engine assembly and align the engine
mount plate (21) with the three engine mounts (24).
IMPORTANT: Make sure not to damage engine, fuel
hose,hydraulichoses,electricalharnessandwires,
controlcables,orotherpartswhileinstalling theen-
gine. Make sure pump hub is in position before
installing the engine mount cap screws.
CAUTION
The muffler and exhaust manifold may be hot.
Avoid possible burns, allow exhaust system to
cool before working on the engine.
2. Alignthepumphub(30)withthepumpshaftandkey
(42)
and slide the pump hub over the pump shaft.
3.
screws (1), flat washers (2), and spacers (3).
Install the three engine mount flange nuts (7), cap
2.
tery.
Disconnect the negative (--) battery cable at the bat-
A. Torque cap screws from 27 to 33 ft--lb (36 to 45
Nm).
DANGER
4.
Mount the hydraulic pump assembly to the pump
adapter (19) using two cap screws (43) lock washers
Gasolineisflammable.Usecautionwhenstoring
or handling it. Do not smoke while filling the fuel
tank. Do not fill fuel tank while engine is running
or in an enclosed area. Always fill fuel tank out-
side and wipe up any spilled fuel before starting
the engine. Store fuel in a clean, safety--ap-
proved container, and keep the cap in place. Use
gasoline for the engine only; not for any other
purpose.
(42)
and hardened washers (32).
A. Torque cap screws from 27 to 33 ft--lb (36 to 45
Nm).
B. Tightenpumphubsetscrews(41)from90to110
in--lb (10.2 to 12.4 Nm).
5.
Connect the engine wiring harness (29) and ground
wires (11) to the engine.
3.
Close fuel shut--off valve (15 Fig. 4).
6.
Connect and adjust the choke control cable (see
4.
Remove the fuel hose support clamp (11 Fig. 4) and
Adjusting the Choke Control in the Traction Unit Opera-
tor’s Manual).
disconnect fuel hose (3 Fig. 4) at the carburetor. Drain
any fuel trapped in the fuel filter and fuel hose into a suit-
able container.
7.
Connect and adjust the throttle control cable (see
AdjustingtheThrottleControlintheTractionUnitOpera-
tor’s Manual).
5.
Disconnect the engine wiring harness (29), the
choke control cable, the throttle control cable, and the
ground wires (11) at the engine.
8.
hose clamp (18 Fig. 4). Install the fuel hose support
clamp (11 Fig. 4).
Connect fuel hose (3 Fig. 4) to the carburetor with
6.
Loosen the two set screws (41) securing the pump
hub (30) to the pump shaft.
9.
Open fuel shut--off valve (15 Fig. 4) and fill fuel tank
7.
Support the hydraulic pump assembly and remove
with fuel (see Filling Fuel Tank in the Traction Unit Oper-
ator’s Manual). Check fuel hose for leaks.
the two cap screws (43) lock washers (42) and hard-
ened washers (32) securing the pump to the pump
adapter (19). Do Not disconnect the hydraulic hoses or
neutral control linkage from the pump.
10.
Start the engine and check for proper operation.
8.
engine mount flange nuts (7), cap screws (1), flat wash-
ers (2), and spacers (3).
Support the engine assembly and remove the three
9.
Remove the engine.
Greensmaster 3150
Page 3 -- 7 Rev. E
Engine
Categories | Lawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals |
---|---|
Tags | Toro Greensmaster 3150 |
Download File |
|
Document Type | Service Manual |
Language | English |
Product Brand | Toro. Customer Service Representatives are available by phone:
Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower |
Document File Type | |
Publisher | toro.com |
Wikipedia's Page | Toro Company |
Copyright | Attribution Non-commercial |
(1 votes, average: 2 out of 2) Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Safety switches not working