Toro 03113SL Rev E Greensmaster 3150 Service Manual

Flush Hydraulic System
IMPORTANT: Flush the hydraulic  system any time
there is a severe component failure or the system is
contaminated (oil  appears milky  or black or  con-
tains metal particles).
9.   Connect both engine spark plug wires to the spark
plugs.
10.
Start engine and let it idle at low speed for a mini-
mum of two (2) minutes. Increase engine speed to high
idle for a minimum of one (1) minute under no load.
IMPORTANT: Flush hydraulic system when chang-
Ing from  petroleum base  hydraulic fluid.  Operate
machine under normal operating conditions  for at
least four (4) hours before draining.
11.
12.
Raise and lower cutting units several times.
Shut off engine  and check for hydraulic  oil leaks.
Check oil level in hydraulic reservoir and add correct oil
if necessary.
1.
units, stop engine, and engage parking brake.
Park  machine on  a  level surface.  Lower  cutting
13.
Operatethemachinefortwo(2)hoursundernormal
operating conditions.
CAUTION
14.
Check condition of hydraulic oil. If the flushing fluid
showsanysignsofcontamination,orifyouarechanging
to biodegradable fluid, repeat steps 1 through 14 again.
Before continuing further, read and  become fa-
miliar with  General  Precautions for  Removing
and Installing Hydraulic System Components.
15.
Assume   normal  operation   and   follow   recom-
mended maintenance intervals.
2.
Clean area around hydrostat and pump inlet hose.
Clamppumpinlethose.Removeinlethosefromhydros-
tat, release clamp,  and drain reservoir  into a suitable
container. Drain hydraulic system while making sure lift
cylinders, hoses, tube lines, and all other components
are drained from low points while the system is warm.
Discard filter (Fig. 39).
PUMP INLET HOSE
3.
Clean oil  filter mounting  area. Remove  filter and
drain into a suitable container. Discard filter (Fig. 40).
4.
Inspect and clean reservoir (see Inspecting Reser-
voir Parts).
5.
Makesurefiltermountingsurfaceisclean.Applyhy-
Figure 39
draulic oil to gasket on the new filter. Screw filter on until
gasket contacts mounting plate, then tighten filter half a
turn.
Note:
Use only hydraulic fluids (including biodegrad-
able) specified in the Traction Unit Operator’s Manual.
Other fluids could cause system damage.
6.
disconnected prior to draining. Fill hydraulic reservoir.
Reconnect all hydraulic hoses and lines that were
7.
Disconnect both engine spark plug wires from  the
spark plugs.
8.
(10)
tooffandwaitoneminutetoallowstartertocool.Repeat
step a second time.
Turn ignition key switch and engage starter for ten
seconds to the prime pump. Return ignition switch
HYDRAULIC OIL FILTER
Figure 40
Greensmaster 3150
Page 4 -- 65
Hydraulic System (Rev. E)
Product Specification
CategoriesLawn Mower Manual, Sprinkler and Irrigation Manuals, Toro Sprinkler and Irrigation Manuals
Tags
Download File
Please Enter the Security Characters Shown Below. Letters are Case Sensitive. Your download link will appear upon completing this step.
- 306 pages
Document TypeService Manual
LanguageEnglish
Product BrandToro. Customer Service Representatives are available by phone: Monday - Friday 7:30 a.m. to 9:00 p.m. (CDT) - Saturday 8:00 a.m. to 8:00 p.m. (CDT) - Sunday 10:00 a.m. to 8:00 p.m. (CDT)
Canada 1-888-225-4886 USA 1-888-384-9939, Lawn Mower
Document File TypePDF
Publishertoro.com
Wikipedia's PageToro Company
CopyrightAttribution Non-commercial
(1 votes, average: 2 out of 2)
Lawn and Garden readers have rated Toro 03113SL Rev E Greensmaster 3150 Service Manual 2.0 out of 2.0 based on 1 product reviews.
Submit your review (optional)
(will not be displayed)
* Required Field

Toro 03113SL Rev E Greensmaster 3150 Service Manual SKU UPC Model
kurt on May 29, 2014.

Safety switches not working


Leave a Reply

Your email address will not be published. Required fields are marked *

*
*
Website